{"title":"Battery Charger","description":"\n\u003cp\u003eAn automotive battery charger converts mains power into controlled DC current to restore or maintain a 12- or 24-volt battery. Smart chargers vary voltage through bulk, absorption, float and sometimes desulphation stages. Charger mode must match lead-acid, AGM, EFB, gel or lithium chemistry; one generic setting is not safe for every battery.\u003c\/p\u003e\n\u003cp\u003eSelect by battery voltage, chemistry, capacity, vehicle electronics and charging purpose. Confirm output current, maintenance mode, temperature compensation, lithium battery-management compatibility, reverse-polarity protection, weather rating and whether the vehicle allows in-situ charging. A high-current starter\/booster is not the same as a long-term charger.\u003c\/p\u003e\n\u003cp\u003eInspect the battery before connecting. Do not charge a cracked, leaking, frozen, swollen or excessively hot battery. Lead-acid charging can release explosive hydrogen and corrosive acid mist; work in ventilation, wear eye protection and keep flames, sparks and smoking away. Lithium packs showing damage, heat or swelling need manufacturer emergency handling, not routine charging.\u003c\/p\u003e\n\u003cp\u003eSwitch the charger off and unplug it while making connections unless its instructions state otherwise. Connect the positive lead to the approved positive terminal, then the negative lead to the specified battery or chassis point. On vehicles with battery-monitoring sensors, the negative connection often belongs on the body side so charge current is measured.\u003c\/p\u003e\n\u003cp\u003eSelect the correct programme only after verifying battery identity. Do not use a desulphation or high-voltage repair mode while connected to vehicle electronics unless explicitly approved. Monitor the first charging period for heat, odour, bubbling, cable damage or error messages and stop if anything is abnormal.\u003c\/p\u003e\n\u003cp\u003eWhen complete, switch off\/unplug before removing negative then positive leads as directed. Verify resting voltage and, where relevant, state of charge, conductance or load performance. Charging cannot repair an internally shorted cell, poor alternator, parasitic drain or loose terminals. Record the selected mode and any charger fault code because they can help distinguish a setup error from a battery that will not accept charge. Suitable automotive battery chargers are listed below.\u003c\/p\u003e","products":[{"product_id":"maypole-7423a-battery-charger-4a-12v-auto-electr","title":"Intelligent Battery Charger - 4A - 6V\/12V","description":"\u003cul\u003e\n\u003cli\u003eIP65\u003c\/li\u003e\n\u003cli\u003eSuitable for low maintenance and maintenance-free batteries\u003c\/li\u003e\n\u003cli\u003eManufactured to European electrical safety standards\u003c\/li\u003e\n\u003cli\u003eOverload, reverse-polarity and short circuit protection\u003c\/li\u003e\n\u003cli\u003eInterchangeable 1.5m battery clip \u0026amp; ring terminal connector leads included\u003c\/li\u003e\n\u003cli\u003eLCD display with battery level indicator and dual colour backlight\u003c\/li\u003e\n\u003cli\u003eMemory function automatically re-starts charging if interrupted\u003c\/li\u003e\n\u003cli\u003e5 step charging including recovery \u0026amp; maintenance cycles\u003c\/li\u003e\n\u003cli\u003e4 charging modes : 12V Standard, AGM \u0026amp; Winter; 6V Standard\u003c\/li\u003e\n\u003cli\u003eAutomatic charging current selection\u003c\/li\u003e\n\u003cli\u003eAutomatic detection of battery voltage \u0026amp; condition\u003c\/li\u003e\n\u003cli\u003eOutputs: 6V: 4A DC 12V:4A DC\u003c\/li\u003e\n\u003cli\u003eInput: 230V AC 50Hz 0.6A\u003c\/li\u003e\n\u003cli\u003eNot recommended for use with GEL batteries\u003c\/li\u003e\n\u003cli\u003eSuitable for use with 6V \u0026amp; 12V lead-acid and 12V AGM batteries of 1.2Ah to 120Ah\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e150\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e290\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e60\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.776\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nWhether your car battery struggles because of the cold, lack of use or even because you've accidentally left your lights on, battery chargers are a great way to get your battery back up and running and maintaining it.\u003cp\u003eThis 3.8 Amp electronic battery charger ensures by itself that you don't overcharge and damage your vehicle's battery. It is fully automatic, meaning it will diagnose, recover, charge and maintain batteries for months. It is also MCU (Microcontroller Unit) operated, allowing you to easily interact with the charger in a comfortable manner whilst protecting the battery against user errors.  In addition, this battery charger offers overheat protection, protection against short circuit and wrong connections and is also spark proof.\u003c\/p\u003e\u003cp\u003eMaypole was established over 40 years ago beginning with the manufacturing of trailer lighting boards and since then has grown into one of the premier companies in Europe offering ranges of products for the Towing, Trailer, Automotive Aftermarket, Leisure, Agriculture and Marine markets. The company is proud that it is still an independent and family owned business, with total focus on Customers, Quality and Service.\u003c\/p\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339233472892,"sku":"7423A","price":43.45,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/7423A.jpg?v=1771527546"},{"product_id":"maypole-mp7104-battery-charger-4a-led-automatic-12v","title":"Battery Charger - 4A - 12V - LED Automatic","description":"\u003cp\u003eThe Battery Charger - 4A - 12V - LED Automatic is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Input: 230V AC 50Hz Output: 12V DC 2.6A (EN Rated) 4A Max technical info. Use Maypole reference MP7104 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for low maintenance and maintenance free 12V lead acid \u0026amp; AGM batteries of 20Ah to 100Ah capacity only\u003c\/li\u003e\n\u003cli\u003eManufactured to European electrical safety standards\u003c\/li\u003e\n\u003cli\u003e1.7m leads with inline fuse protection and fully insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eOvercharge, short \u0026amp; reverse polarity protection\u003c\/li\u003e\n\u003cli\u003eCompact robust case with integral handle\u003c\/li\u003e\n\u003cli\u003eLED indicators showing charging progress\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003eFully automatic - easy to use and safe\u003c\/li\u003e\n\u003cli\u003eSuitable for lead acid \u0026amp; AGM batteries up to 1.8lt\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eInput: 230V AC 50Hz\u003c\/li\u003e \u003cli\u003eOutput: 12V DC 2.6A (EN Rated) 4A Max\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e180\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e210\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e105\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.865\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339233866108,"sku":"MP7104","price":23.38,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7104.jpg?v=1771543271"},{"product_id":"maypole-mp7106-battery-charger-6a-led-automatic-12v","title":"Battery Charger 6A - 12V - LED Automatic","description":"\u003cp\u003eThe Battery Charger 6A - 12V - LED Automatic is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Input: 230V AC 50Hz Output: 12V DC 4.0A (EN Rated) 6A Max technical info. Use Maypole reference MP7106 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for low maintenance and maintenance free 12V lead acid \u0026amp; AGM batteries of 20Ah to 100Ah capacity only\u003c\/li\u003e\n\u003cli\u003eManufactured to European electrical safety standards\u003c\/li\u003e\n\u003cli\u003e1.7m leads with inline fuse protection and fully insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eOvercharge, short \u0026amp; reverse polarity protection\u003c\/li\u003e\n\u003cli\u003eCompact robust case with integral handle\u003c\/li\u003e\n\u003cli\u003eLED indicators showing charging progress\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003eFully automatic - easy to use and safe\u003c\/li\u003e\n\u003cli\u003eSuitable for lead acid \u0026amp; AGM batteries up to 1.8lt\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eInput: 230V AC 50Hz\u003c\/li\u003e \u003cli\u003eOutput: 12V DC 4.0A (EN Rated) 6A Max\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e175\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e205\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e105\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e2.281\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339234128252,"sku":"MP7106","price":26.06,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7106.jpg?v=1771543273"},{"product_id":"maypole-mp7108-battery-charger-8a-led-automatic-6v-12v","title":"Battery Charger 8A - 6V\/12V - LED Automatic","description":"\u003cp\u003eThe Battery Charger 8A - 6V\/12V - LED Automatic is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Input: 230V AC 50Hz 6V DC 5.1A (EN Rated) 8A Max 12V DC 5.1A (EN Rated) 8A Max technical info. Use Maypole reference MP7108 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for low maintenance and maintenance free 12V lead acid \u0026amp; AGM batteries of 20Ah to 100Ah capacity only\u003c\/li\u003e\n\u003cli\u003eManufactured to European electrical safety standards\u003c\/li\u003e\n\u003cli\u003e1.7m leads with inline fuse protection and fully insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eOvercharge, short \u0026amp; reverse polarity protection\u003c\/li\u003e\n\u003cli\u003eCompact robust case with integral handle\u003c\/li\u003e\n\u003cli\u003eLED indicators showing charging progress\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003eFully automatic - easy to use and safe\u003c\/li\u003e\n\u003cli\u003eSuitable for lead acid \u0026amp; AGM batteries up to 1.8lt\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eInput: 230V AC 50Hz\u003c\/li\u003e \u003cli\u003e6V DC 5.1A (EN Rated) 8A Max\u003c\/li\u003e \u003cli\u003e12V DC 5.1A (EN Rated) 8A Max\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e195\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e270\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e125\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e3.23\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339234423164,"sku":"MP7108","price":36.02,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7108.jpg?v=1771543274"},{"product_id":"maypole-mp7212-automatic-workshop-charger-12a-75a","title":"Automatic Workshop Charger - 12A\/75A","description":"\u003cp\u003eThe Automatic Workshop Charger - 12A\/75A is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Use Maypole reference MP7212 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e1.8m leads with fully insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eLED indicator for reverse polarity\u003c\/li\u003e\n\u003cli\u003eSuitable for start\/stop technology\u003c\/li\u003e\n\u003cli\u003e4 charging rate options (12V 3A \u0026amp; 12A; 24V 3A \u0026amp; 6A)\u003c\/li\u003e\n\u003cli\u003eFast charge\u003c\/li\u003e\n\u003cli\u003eDisplay showing key charging information (Volts, Amps, % of full battery capacity)\u003c\/li\u003e\n\u003cli\u003eRobust metal case\u003c\/li\u003e\n\u003cli\u003eEasy to use and safe\u003c\/li\u003e\n\u003cli\u003eIncrease performance and battery life\u003c\/li\u003e\n\u003cli\u003eFully automatic charging cycles for optimum charging\/maintenance and safety\u003c\/li\u003e\n\u003cli\u003eSuitable for 12\/24V lead acid\/AGM and GEL batteries\u003c\/li\u003e\n\u003cli\u003eSuitable for heavy duty batteries from 6-200Ah\u003c\/li\u003e\n\u003cli\u003eAutomatic workshop charger 12Amp with 75Amp engine start, the smart charging solution for modern vehicle batteries\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e315\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e205\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e310\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e5.678\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339234685308,"sku":"MP7212","price":81.46,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7212.jpg?v=1771543278"},{"product_id":"maypole-mp7220-automatic-workshop-charger-12v24v","title":"Automatic Workshop Charger - 20A\/150A","description":"\u003cp\u003eThe Automatic Workshop Charger - 20A\/150A is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Use Maypole reference MP7220 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e1.8m leads with fully insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eLED indicator for reverse polarity\u003c\/li\u003e\n\u003cli\u003eSuitable for start\/stop technology\u003c\/li\u003e\n\u003cli\u003e4 charging rate options (12V 3A \u0026amp; 12A; 24V 3A \u0026amp; 6A)\u003c\/li\u003e\n\u003cli\u003eFast charge\u003c\/li\u003e\n\u003cli\u003eDisplay showing key charging information (Volts, Amps, % of full battery capacity)\u003c\/li\u003e\n\u003cli\u003eRobust metal case\u003c\/li\u003e\n\u003cli\u003eEasy to use and safe\u003c\/li\u003e\n\u003cli\u003eIncrease performance and battery life\u003c\/li\u003e\n\u003cli\u003eFully automatic charging cycles for optimum charging\/maintenance and safety\u003c\/li\u003e\n\u003cli\u003eSuitable for 12\/24V lead acid\/AGM and GEL batteries\u003c\/li\u003e\n\u003cli\u003eSuitable for heavy duty batteries from 6-200Ah\u003c\/li\u003e\n\u003cli\u003eAutomatic workshop charger 12Amp with 75Amp engine start, the smart charging solution for modern vehicle batteries\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e315\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e205\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e310\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e8.375\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339234881916,"sku":"MP7220","price":94.82,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7220.jpg?v=1771543279"},{"product_id":"maypole-mp7402-automatic-trickle-battery-charger","title":"Automatic Trickle Battery Charger - 0.5A - 12V","description":"\u003cp\u003eThe Automatic Trickle Battery Charger - 0.5A - 12V is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Maypole reference MP7402 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eProtection against thermal and current overload, reverse-polarity and incorrect connection with spark free crocodile clips\u003c\/li\u003e\n\u003cli\u003e4 step cycle: Diagnosis, bulk, absorption \u0026amp; maintenance charging modes\u003c\/li\u003e\n\u003cli\u003eAutomatic detection of battery voltage and condition and dual colour LED charging status indicator\u003c\/li\u003e\n\u003cli\u003eSuitable for 12V lead-acid batteries (wet, maintenance-free, AGM \u0026amp; GEL) up to 100Ah only\u003c\/li\u003e\n\u003cli\u003e12V \/ 0.5A fully automatic plug-in battery charger ideal for maintenance charging\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003eManufactured to European electrical safety standards;Input 220-240V AC 50Hz 0.2A;Output 12V DC 0.5A;For indoor use only;Protection class IP20;Max Lead-acid battery capacity 100Ah;Conforms to EN60335-1, EN60335-2-29, EN55014, EN61000, 73\/23 CEE, 93\/68 CEE,\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e195\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e77\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.333\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nMany car batteries struggle in the winter and spring time due to cold weather and lack of use. Jump leads are a great way of getting your car going when you have a flat battery, but using them constantly will have a negative effect in the long term as you will be continually discharging the battery. Therefore, maintaining your battery's charge is a far more cost effective way of starting your car with less hassle. Trickle chargers are a great way of maintaining a battery's charge. This Maypole 12V automatic trickle charger is to be used indoors, by simply connecting your car battery to the charger. You can then leave it charging until the next time you need to use it, when you can have confidence in knowing that it will work. Established in 1969, Birmingham based company Maypole has a long heritage in the manufacture and marketing of products to customers in the automotive, trailer, leisure and agricultural markets. For over 40 years Maypole have been manufacturing and supplying its products to its ever growing network of customers and are proud to continue to add to their ever increasing portfolio of products.","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339235242364,"sku":"MP7402","price":19.66,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7402.jpg?v=1771543280"},{"product_id":"maypole-mp7404-compact-battery-charger-4a-12v","title":"Compact Battery Charger - 4A - 12V","description":"\u003cp\u003eThe Compact Battery Charger - 4A - 12V is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Suitable for 12V lead acid \u0026amp; AGM batteries of 10Ah to 60Ah capacity only Output 4A technical info. Use Maypole reference MP7404 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for 12V applications\u003c\/li\u003e\n\u003cli\u003eLED indicators showing charging status\u003c\/li\u003e\n\u003cli\u003eHandy Cable Tie for compact storage\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003eFully Insulated Crocodile Clips\u003c\/li\u003e\n\u003cli\u003eCompact robust case with integral handle\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eSuitable for 12V lead acid \u0026amp; AGM batteries of 10Ah to 60Ah capacity only\u003c\/li\u003e \u003cli\u003eOutput 4A\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e160\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e200\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.23\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339235897724,"sku":"MP7404","price":17.94,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7404.jpg?v=1771543284"},{"product_id":"maypole-mp7406-compact-battery-charger-6a-12v","title":"Compact Battery Charger - 6A - 12V","description":"\u003cp\u003eThe Compact Battery Charger - 6A - 12V is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Suitable for 12V lead acid \u0026amp; AGM batteries of 12Ah to 80Ah capacity only Output 4A technical info. Use Maypole reference MP7406 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for 12V applications\u003c\/li\u003e\n\u003cli\u003eLED indicators showing charging status\u003c\/li\u003e\n\u003cli\u003eHandy Cable Tie for compact storage\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003eFully Insulated Crocodile Clips\u003c\/li\u003e\n\u003cli\u003eCompact robust case with integral handle\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eSuitable for 12V lead acid \u0026amp; AGM batteries of 12Ah to 80Ah capacity only\u003c\/li\u003e \u003cli\u003eOutput 4A\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e160\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e200\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.41\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339236225404,"sku":"MP7406","price":19.74,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7406.jpg?v=1771543285"},{"product_id":"maypole-mp7428-battery-charger-8a-12v-electronic-smart","title":"Battery Charger - 8A - 12V - Electronic Smart","description":"\u003cp\u003eThe Battery Charger - 8A - 12V - Electronic Smart is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Maypole reference MP7428 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSupplied in modern display packaging\u003c\/li\u003e\n\u003cli\u003eLED error indicator for reverse polarity, short circuit or open circuit\u003c\/li\u003e\n\u003cli\u003eSuitable for cars, vans and leisure vehicles up to 5L\u003c\/li\u003e\n\u003cli\u003eOutput 8A\u003c\/li\u003e\n\u003cli\u003eSuitable for 12V applications\u003c\/li\u003e\n\u003cli\u003eAutomatic 9 stage charging cycle, including diagnosis; charging \u0026amp; reconditioning\u003c\/li\u003e\n\u003cli\u003eOverheat, overcurrent and overcharge protection\u003c\/li\u003e\n\u003cli\u003eLCD display showing charging information (battery voltage; charging current; % of full battery capacity)\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003e1.5m output leads fitted with insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eFor use with batteries 1.2Ah - 192Ah in capacity (Lead Acid \u0026amp; AGM)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e120\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e280\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e110\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.935\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56339236585852,"sku":"MP7428","price":49.05,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7428.jpg?v=1771543286"},{"product_id":"napa-consumables-nc16a-napa-16a-double-voltage-smart-charger","title":"Multi-Stage Fully Automatic Smart Charger","description":"\u003cp\u003eThe Multi-Stage Fully Automatic Smart Charger is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Napa consumables reference NC16A when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ein.4 x built in safety functions -over load\/ over heat\/ short circuit\/ reverse polarityin.\u003c\/li\u003e\n\u003cli\u003eQuick connectors with clamps or O-ring terminals for long term connection\u003c\/li\u003e\n\u003cli\u003eLarge LCD display screen that clearly shows voltage and charging progress\u003c\/li\u003e\n\u003cli\u003eSuitable for lead acid, AGM and Gel batteries\u003c\/li\u003e\n\u003cli\u003e9 stage charging process\u003c\/li\u003e\n\u003cli\u003eMicro Processor controlled\u003c\/li\u003e\n\u003cli\u003e6\/12V Dual Voltage\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e256\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e92\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e225\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.74\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n16 amp smart charger and battery maintainer. Compatible with lead acid, gel, calcium, EFB and AGM batteries.","brand":"NAPA CONSUMABLES","offers":[{"title":"1","offer_id":56339237601660,"sku":"NC16A","price":61.54,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/NC16A_1.jpg?v=1771546474"},{"product_id":"napa-consumables-nc8a-napa-8a-double-voltage-smart-charger","title":"Multi-Stage Fully Automatic Smart Charger","description":"\u003cp\u003eThe Multi-Stage Fully Automatic Smart Charger is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Napa consumables reference NC8A when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ein.4 x built in safety functions -over load\/ over heat\/ short circuit\/ reverse polarityin.\u003c\/li\u003e\n\u003cli\u003eQuick connectors with clamps or O-ring terminals for long term connection\u003c\/li\u003e\n\u003cli\u003eLarge LCD display screen that clearly shows voltage and charging progress\u003c\/li\u003e\n\u003cli\u003eSuitable for lead acid, AGM and Gel batteries\u003c\/li\u003e\n\u003cli\u003e9 stage charging process\u003c\/li\u003e\n\u003cli\u003eMicro Processor controlled\u003c\/li\u003e\n\u003cli\u003e6\/12V Dual Voltage\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e235\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e80\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e180\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.22\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n8 amp smart charger and battery maintainer. Compatible with lead acid, gel, calcium, EFB and AGM batteries.","brand":"NAPA CONSUMABLES","offers":[{"title":"1","offer_id":56339237962108,"sku":"NC8A","price":43.86,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/NC8A_1.jpg?v=1771546475"},{"product_id":"ring-rsc612-12a-12v-smart-battery-charger","title":"Multi-Stage Fully Automatic Smart Charger","description":"\u003cp\u003eThe Multi-Stage Fully Automatic Smart Charger is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Ring reference RSC612 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for vehicles up to 5L\u003c\/li\u003e\n\u003cli\u003eBattery Capacity: 25-300Ah\u003c\/li\u003e\n\u003cli\u003eCharging current up to 12A\u003c\/li\u003e\n\u003cli\u003eRubber wrap outer for added protection and grip\u003c\/li\u003e\n\u003cli\u003eMemory saver function allows vehicle and audio settings to be retained if the battery is removed from the vehicle\u003c\/li\u003e\n\u003cli\u003eInteractive LCD display which shows charge status, mode selected and the condition of the battery\u003c\/li\u003e\n\u003cli\u003eBattery cranking performance - measures the battery's cold cranking performance to determine engine starting ability\u003c\/li\u003e\n\u003cli\u003eAlternator check - tests the recharging performance of the vehicles alternator\u003c\/li\u003e\n\u003cli\u003eStart power test - measures voltage drop during engine start to identify battery issues\u003c\/li\u003e\n\u003cli\u003eIncludes the following battery and alternator analysis tools:\u003c\/li\u003e\n\u003cli\u003eIncludes battery repair tools to increase performance and battery life\u003c\/li\u003e\n\u003cli\u003eAuto Charge applies the fastest charge, based on battery size\u003c\/li\u003e\n\u003cli\u003eIncludes settings for both standard \u0026amp; START\/STOP batteries\u003c\/li\u003e\n\u003cli\u003eMulti-stage, fully automatic smart charger with interactive LCD display, battery \u0026amp; alternator analysis modes and repair tools\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e94\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e278\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e270\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.772\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe Ring RSC612 multi-stage, fully automatic smart charger carries out a multitude of functions in one. Carrying out analysis, repair and charging of batteries automatically, it is more than a standard smart charger.  The interactive LCD display shows charge status, mode selected and condition of battery. Analysis mode determines performance of vehicle battery and alternator. It also includes settings for standard and start\/stop vehicles to ensure it is suitable for all ages of vehicles","brand":"RING","offers":[{"title":"1","offer_id":56339239272828,"sku":"RSC612","price":114.29,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/RSC612.jpg?v=1771551168"},{"product_id":"ring-rsc804-4amp-smart-battery-charger-uk","title":"Multi-Stage Fully Automatic Smart Charger","description":"\u003cul\u003e\n\u003cli\u003eConnect and be sure - automatically adjusts to long-term maintenance mode when battery is full\u003c\/li\u003e\n\u003cli\u003eReverse polarity and short-circuit protection\u003c\/li\u003e\n\u003cli\u003eBacklit display can be seen in low light\u003c\/li\u003e\n\u003cli\u003eOne button operation for ease-of-use\u003c\/li\u003e\n\u003cli\u003eQuick connectors with clamps or O-ring terminals for long term connection\u003c\/li\u003e\n\u003cli\u003eCold weather charging mode that protects batteries in cold temperatures\u003c\/li\u003e\n\u003cli\u003eLarge LCD display screen that clearly shows voltage and charging process\u003c\/li\u003e\n\u003cli\u003e7-Stage charging process\u003c\/li\u003e\n\u003cli\u003eStop\/Start compatible\u003c\/li\u003e\n\u003cli\u003eSmart charger and battery maintainer\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e118\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e255\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e118\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.908\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n\u003cp\u003eThe Ring RSC804 is a 4A smart charger and battery maintainer suitable for 6V and 12V vehicles and recommended for START\/STOP batteries. Compatible with lead acid, gel, calcium, EFB and AGM batteries. Keeps batteries in good condition without risk of overcharging. One button operation and large LCD backlit display for ease of use as well as reverse polarity and short-circuit protection for safety. Connect and be sure with the charger adjusting automatically to long-term maintenance mode when the vehicle's battery is full.\u003c\/p\u003e  \u003cp\u003eAvailable with three pin plug (part number RSC804) and two pin plug (part number RESC804)\u003c\/p\u003e","brand":"RING","offers":[{"title":"1","offer_id":56339239666044,"sku":"RSC804","price":28.46,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/RSC804_1.jpg?v=1771551170"},{"product_id":"ring-rsc806-6amp-smart-battery-charger-uk","title":"Multi-Stage Fully Automatic Smart Charger","description":"\u003cul\u003e\n\u003cli\u003eConnect and be sure - automatically adjusts to long-term maintenance mode when battery is full\u003c\/li\u003e\n\u003cli\u003eReverse polarity and short-circuit protection\u003c\/li\u003e\n\u003cli\u003eBacklit display can be seen in low light\u003c\/li\u003e\n\u003cli\u003eOne button operation for ease-of-use\u003c\/li\u003e\n\u003cli\u003eQuick connectors with clamps or O-ring terminals for long term connection\u003c\/li\u003e\n\u003cli\u003eCold weather charging mode that protects batteries in cold temperatures\u003c\/li\u003e\n\u003cli\u003eLarge LCD display screen that clearly shows voltage and charging process\u003c\/li\u003e\n\u003cli\u003e7-Stage charging process\u003c\/li\u003e\n\u003cli\u003eStop\/Start compatible\u003c\/li\u003e\n\u003cli\u003eSmart charger and battery maintainer\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e288\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e285\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e128\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.142\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n\u003cp\u003e6A smart charger, for both 6V and 12V vehicles. Recommended for START\/STOP batteries as well as being compatible with lead, gel, calcium, AGM and EFB battery types. Keeps batteries in good condition without risk of overcharging. One button operation and large backlit digital display for ease of use as well as reverse polarity and short-circuit protection for safety. Connect and be sure that there won't be any over charging as a result of using the smart charger with the charger adjusting automatically to long-term maintenance mode when the vehicle's battery is full.\u003c\/p\u003e  \u003cp\u003eAvailable with three pin plug (part number RSC806) and two pin plug (part number RESC806)\u003c\/p\u003e","brand":"RING","offers":[{"title":"1","offer_id":56339239960956,"sku":"RSC806","price":41.51,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/RSC806_1.jpg?v=1771551172"},{"product_id":"ring-rsp1000-12a-12v-smart-battery-charger","title":"Ring 10W Solar Battery Maintainer","description":"\u003cp\u003eThe Ring 10W Solar Battery Maintainer is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Use Ring reference RSP1000 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCompatible with OBDII port Solar Power Cable RSPOBDN\u003c\/li\u003e\n\u003cli\u003e3m Power Cable for easy connection\u003c\/li\u003e\n\u003cli\u003ePolarity protection to prevent damage of clamps connected to the wrong battery terminals\u003c\/li\u003e\n\u003cli\u003eCrocodile Clamps for direct charging into the battery\u003c\/li\u003e\n\u003cli\u003eSupplied with 12V power connection for easy charging\u003c\/li\u003e\n\u003cli\u003eWorks in overcast conditions\u003c\/li\u003e\n\u003cli\u003eIP65 rated making it water resistant\u003c\/li\u003e\n\u003cli\u003eIdeal for caravans, small cars, motorbikes, golf trolleys and jet skis\u003c\/li\u003e\n\u003cli\u003eMonocrystalline solar cells which are more efficient than older amorphous solar cells\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e428\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e32\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e242\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.362\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nModern vehicles have a small but constant battery drain. Packed full of electrical systems that are constantly working even when the ignition is not running. Alarms immobilisers and lock monitoring are examples of systems running in the background that can cause the battery to discharge even when the vehicle is not being used. The RSP1000 is a solar powered battery maintainer for 12V vehicles. The low carbon environmentally free way to maintain your vehicle battery when not in use. Ideal for seasonally-used vehicles such as caravans, classic cars, motorcycles, and golf trolleys. Supplied with DC power plug and battery clips. Works in overcast conditions and is water resistant. Reverse polarity protection prevents damage if the clamps are connected to the incorrect battery poles.","brand":"RING","offers":[{"title":"1","offer_id":56339240321404,"sku":"RSP1000","price":42.69,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/RSP1000.jpg?v=1771551179"},{"product_id":"ring-rsp500-5w-mono-solar-cell-batt-maintain","title":"Ring 5W Solar Battery Maintainer","description":"\u003cp\u003eThe Ring 5W Solar Battery Maintainer is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Use Ring reference RSP500 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCompatible with OBDII port Solar Power Cable RSPOBDN\u003c\/li\u003e\n\u003cli\u003e3m Power Cable for easy connection\u003c\/li\u003e\n\u003cli\u003ePolarity protection to prevent damage of clamps connected to the wrong battery terminals\u003c\/li\u003e\n\u003cli\u003eCrocodile Clamps for direct charging into the battery\u003c\/li\u003e\n\u003cli\u003eSupplied with 12V power connection for easy charging\u003c\/li\u003e\n\u003cli\u003eWorks in overcast conditions\u003c\/li\u003e\n\u003cli\u003eIP65 rated making it water resistant\u003c\/li\u003e\n\u003cli\u003eIdeal for caravans, small cars, motorbikes, golf trolleys and jet skis\u003c\/li\u003e\n\u003cli\u003eMonocrystalline solar cells which are more efficient than older amorphous solar cells\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e31\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e311\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e247\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.94\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nModern vehicles have a small but constant battery drain. They are packed full of electrical systems that are constantly working even when the ignition is not running. Alarms immobilisers and lock monitoring are examples of systems running in the background that can cause the battery to discharge even when the vehicle is not being used. The RSP500 is a solar powered battery maintainer for 12V vehicles. The low carbon environmentally free way to maintain your vehicle battery when not in use. Ideal for seasonally-used vehicles such as caravans classic cars motorcycles and golf trolleys. Supplied with DC power plug and battery clips Works in overcast conditions and is water resistant. Reverse polarity protection prevents damage if the clamps are connected to the incorrect battery poles.","brand":"RING","offers":[{"title":"1","offer_id":56339240583548,"sku":"RSP500","price":33.35,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/RSP500.jpg?v=1771551180"},{"product_id":"gys-024588-1524-intel-charger-12v-24v","title":"Batium 15.24 Smart Charger","description":"\u003cp\u003eThe Batium 15.24 Smart Charger is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Gys reference 024588 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSafe for all types of Lead Acid batteries even when the type is unknown\u003c\/li\u003e\n\u003cli\u003eThe Batium 15.24 will not deliver current if there is no battery detected (no voltage in the clamps).\u003c\/li\u003e\n\u003cli\u003eAnti-spark feature which prevents sparks whilst connecting the Gysflash to the battery.\u003c\/li\u003e\n\u003cli\u003eProtected against short-circuits, polarity reversals and vehicle start\u003c\/li\u003e\n\u003cli\u003eSOS recovery GO \u0026gt;0.5V\u003c\/li\u003e\n\u003cli\u003eThe BATIUM range is a microprocessor-controlled smart charger, it constantly analyses the battery's condition and regulates the charging process accordingly.\u003c\/li\u003e\n\u003cli\u003eFull charge and 100% charge level maintenance.\u003c\/li\u003e\n\u003cli\u003eCharges 50% faster than a traditional charger.\u003c\/li\u003e\n\u003cli\u003eCan be used on batteries for motorcycles, collector's vehicles, light vehicles, vans, agricultural machinery, public works vehicles, heavy goods vehicles and buses from 35 to 225 Ah.\u003c\/li\u003e\n\u003cli\u003eProtection of on-board electronics.\u003c\/li\u003e\n\u003cli\u003eRecovery of heavily discharged batteries (from 2 V).\u003c\/li\u003e\n\u003cli\u003eAutomatic charger for all types of lead-acid batteries (Gel, liquid, AGM, VRLA) 6\/12\/24V\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003ecert024588 (1).pdf\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e210\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e143\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e362\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e7.1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nAutomatic charger for all types of lead-acid batteries (gel, liquid, AGM, VRLA) 6\/12\/24 V. Can be used for batteries on motorcycles, collector's vehicles, light vehicles, vans, agricultural machinery, public works vehicles, heavy goods vehicles and buses from 35 to 225 Ah.","brand":"GYS","offers":[{"title":"1","offer_id":56342253830524,"sku":"024588","price":217.12,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/024588.jpg?v=1771519300"},{"product_id":"noco-genius1uk-1a-battery-charger","title":"Smart Battery Charger - 6V\/12V - 1A","description":"\u003cp\u003eThe Smart Battery Charger - 6V\/12V - 1A is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Noco reference GENIUS1UK when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShort-Circuit: Yes | Open-Circuit: Yes | Overheating: Yes | Overcharge: Yes | Spark-Proof: Yes | Reverse Polarity: Yes\u003c\/li\u003e\n\u003cli\u003e3-Year Limited Warranty\u003c\/li\u003e\n\u003cli\u003eThe M6 eyelet clamps have wide clamping range and improved clamping force for higher conductivity.\u003c\/li\u003e\n\u003cli\u003eProvides all-season and all-weather charging for a healthy battery.\u003c\/li\u003e\n\u003cli\u003eCharge safely 24\/7 without any risk of overcharging your batteries, plus additional safety like spark-proof connections, and reverse polarity protection.\u003c\/li\u003e\n\u003cli\u003eAn ultra-compact and high-efficiency design with maximum power density and detailed dynamic battery tracking.\u003c\/li\u003e\n\u003cli\u003eCompatible with all types of vehicles.\u003c\/li\u003e\n\u003cli\u003eAutomatically repairs and reverses battery damage caused by sulfation and acid stratification to restore performance and extend battery life.\u003c\/li\u003e\n\u003cli\u003eCharges dead batteries as low as 0-volts in the new 'Force Mode'.\u003c\/li\u003e\n\u003cli\u003eAlters the charge to eliminate over-charging in hot climates and under-charging in cold climates.\u003c\/li\u003e\n\u003cli\u003eDesigned for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eOperating requirements - Line Voltage: 120V to 240V AC\u003c\/li\u003e \u003cli\u003eFrequency: 50Hz to 60Hz\u003c\/li\u003e \u003cli\u003eOperating Temperature: -4° to 104° F (-20° to 40° C)\u003c\/li\u003e \u003cli\u003eStorage Temperature: -22° to 140° F (-30° to 60° C)\u003c\/li\u003e \u003cli\u003eRelative Humidity: 0 to 95% Non-Condensing\u003c\/li\u003e \u003cli\u003eIP Rating: IP60\u003c\/li\u003e \u003cli\u003eConsumption: 15 Watts (Max)\u003c\/li\u003e \u003cli\u003eEfficiency: 85% (120VAC) \/ 83% (230VAC)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e172\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e102\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e89\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.45\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GENIUS1UK is an ultra-compact and high efficiency 1-Amp 6-volt and 12-volt battery charger, battery maintainer, and battery desulfator for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries. An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates. Charge dead batteries as low as 1-volt, or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts. The GENIUS1UK is a fully-automatic, worry-free battery chargers for year-round use. Restore your battery by detecting sulfation and acid stratification and restoring lost performance for stronger engine starts and extended battery life. Compatible with all types of vehicles. Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, performance cars, racing cars and more.","brand":"NOCO","offers":[{"title":"1","offer_id":56342255501692,"sku":"GENIUS1UK","price":42.17,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUS1UK.jpg?v=1771540935"},{"product_id":"noco-genius2duk-2a-direct-mount-battery-charger","title":"Direct-Mount Battery Charger and Maintainer - 6V - 2A","description":"\u003cp\u003eThe Direct-Mount Battery Charger and Maintainer - 6V - 2A is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Noco reference GENIUS2DUK when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eDC Cable Length: 24 Inches (61cm) | DC Cable Size: 18 AWG | DC Fuse Size: 4 AMP Micro Blade Fuse | AC Cable Length: 24 Inches (61cm) | AC Cable Size: 18 AWG | Oil, gas, grease, water, chemical, UV, abrasion resistant\u003c\/li\u003e\n\u003cli\u003eHeight: 5 Inches (127mm) | Width: 2.3 Inches (58mm) | Depth: 1.5 Inches (38mm) | Weight: 0.5 Pounds (0.23kg)\u003c\/li\u003e\n\u003cli\u003eShort-Circuit: Yes | Open-Circuit: Yes | Overheating: Yes | Overcharge: Yes | Spark-Proof: Yes | Reverse Polarity: Yes\u003c\/li\u003e\n\u003cli\u003e3-Year Limited Warranty\u003c\/li\u003e\n\u003cli\u003eCharge safely 24\/7 without any risk of overcharging your batteries, plus additional safety like spark-proof connections, and reverse polarity protection.\u003c\/li\u003e\n\u003cli\u003eEngineered and tested to withstand rugged working environments, high-heat engine compartments, shock, vibration and even water exposure.\u003c\/li\u003e\n\u003cli\u003eCompatible with all types of vehicles. Combine with any of the GCP Series AC Port Plugs for remote charging access.\u003c\/li\u003e\n\u003cli\u003eAutomatically repairs and reverses battery damage caused by sulfation and acid stratification to restore performance and extend battery life.\u003c\/li\u003e\n\u003cli\u003eCharges dead batteries as low as 1-volt, including flooded, gel, and AGM, as well as automotive, marine, and deep-cycle batteries.\u003c\/li\u003e\n\u003cli\u003eAlters the charge to eliminate over-charging in hot climates and under-charging in cold climates.\u003c\/li\u003e\n\u003cli\u003eSecurely mounts nearby the battery with its rugged snap-fit mounting bracket.\u003c\/li\u003e\n\u003cli\u003eThe all-new direct-mount onboard battery charger for an under-the-hood battery charging system and year-round battery maintenance.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eOperating requirements - Line Voltage: 110V to 240V AC\u003c\/li\u003e \u003cli\u003eFrequency: 50Hz to 60Hz\u003c\/li\u003e \u003cli\u003eOperating Temperature: -4° to 104° F (-20° to 40° C)\u003c\/li\u003e \u003cli\u003eStorage Temperature: -22° to 140° F (-30° to 60° C)\u003c\/li\u003e \u003cli\u003eRelative Humidity: 0 to 95% Non-Condensing\u003c\/li\u003e \u003cli\u003eIP Rating: IP65\u003c\/li\u003e \u003cli\u003eConsumption: 28 Watts (Max)\u003c\/li\u003e \u003cli\u003eEfficiency: 87%\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e165\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e95\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e88\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.34\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GENIUS2DUK is an ultra-compact and high efficiency 2-Amp 12-volt battery charger, battery maintainer, and battery desulfator for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, and AGM, as well as automotive, marine, and deep-cycle batteries. An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates. Charge dead batteries as low as 1-volt. The GENIUS2DUK has zero charge modes. Just plug-in and start charger your battery. It's a fully-automatic, worry-free battery charger for year-round use. Restore your battery by detecting sulfation and acid stratification and restoring lost performance for stronger engine starts and extended battery life. Engineered and tested to withstand rugged working environments, like high-heat engine compartments, shock, vibration, and even water exposure. The GENIUS2DUK is the ultimate mountable on-board battery charger and battery maintainer for any car, boat, truck, RV, or equipment, and is designed to be located in close proximity to the battery. Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, racing cars, perfoormance cars and more.","brand":"NOCO","offers":[{"title":"1","offer_id":56342255665532,"sku":"GENIUS2DUK","price":46.92,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUS2DUK.jpg?v=1771540936"},{"product_id":"noco-genius5uk-5a-battery-charger","title":"Smart Battery Charger - 6V\/12V - 5A","description":"\u003cp\u003eThe Smart Battery Charger - 6V\/12V - 5A is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Noco reference GENIUS5UK when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShort-Circuit: Yes | Open-Circuit: Yes | Overheating: Yes | Overcharge: Yes | Spark-Proof: Yes | Reverse Polarity: Yes\u003c\/li\u003e\n\u003cli\u003e3-Year Limited Warranty\u003c\/li\u003e\n\u003cli\u003eThe M6 eyelet clamps have wide clamping range and improved clamping force for higher conductivity.\u003c\/li\u003e\n\u003cli\u003eProvides all-season and all-weather charging for a healthy battery.\u003c\/li\u003e\n\u003cli\u003eCharge safely 24\/7 without any risk of overcharging your batteries, plus additional safety like spark-proof connections, and reverse polarity protection.\u003c\/li\u003e\n\u003cli\u003eAn ultra-compact and high-efficiency design with maximum power density and detailed dynamic battery tracking.\u003c\/li\u003e\n\u003cli\u003eCompatible with all types of vehicles.\u003c\/li\u003e\n\u003cli\u003eAutomatically repairs and reverses battery damage caused by sulfation and acid stratification to restore performance and extend battery life.\u003c\/li\u003e\n\u003cli\u003eCharges dead batteries as low as 0-volts in the new 'Force Mode'.\u003c\/li\u003e\n\u003cli\u003eAlters the charge to eliminate over-charging in hot climates and under-charging in cold climates.\u003c\/li\u003e\n\u003cli\u003eDesigned for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eOperating requirements - Line Voltage: 120V to 240V AC\u003c\/li\u003e \u003cli\u003eFrequency: 50Hz to 60Hz\u003c\/li\u003e \u003cli\u003eOperating Temperature: -4° to 104° F (-20° to 40° C)\u003c\/li\u003e \u003cli\u003eStorage Temperature: -22° to 140° F (-30° to 60° C)\u003c\/li\u003e \u003cli\u003eRelative Humidity: 0 to 95% Non-Condensing\u003c\/li\u003e \u003cli\u003eIP Rating: IP65\u003c\/li\u003e \u003cli\u003eConsumption: 75 Watts (Max)\u003c\/li\u003e \u003cli\u003eEfficiency: 86% (120VAC\/230VAC)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e203\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e117\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e89\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.84\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GENIUS5UK is an ultra-compact and high efficiency 5-Amp 6-volt and 12-volt battery charger, battery maintainer, and battery desulfator for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries. An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates. Charge dead batteries as low as 1-volt, or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts. The GENIUS5UK is a fully-automatic, worry-free battery chargers for year-round use. Restore your battery by detecting sulfation and acid stratification and restoring lost performance for stronger engine starts and extended battery life. Compatible with all types of vehicles. Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, performance cars, racing cars and more.","brand":"NOCO","offers":[{"title":"1","offer_id":56342255763836,"sku":"GENIUS5UK","price":83.57,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUS5UK.jpg?v=1771540939"},{"product_id":"noco-geniuspro25-pro-battery-charger-25a","title":"Professional 25a Workshop Charger","description":"\u003cp\u003eThe Professional 25a Workshop Charger is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Its catalogue specification records CE\/UKCA technical info. Use Noco reference GENIUSPRO25 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAutomatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life. Plus, cutting-edge battery repair modes for 6-volt, 12-volt, and 24-volt batteries.\u003c\/li\u003e\n\u003cli\u003eDetects batteries as low as 1-volt. Or use the all-new force mode that allows you to manually begin charging dead batteries down to zero volts.\u003c\/li\u003e\n\u003cli\u003eAn integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates to maximize battery life and enable fast charging.\u003c\/li\u003e\n\u003cli\u003eA dual-voltage power supply - 12-volt (50-amp) and 24-volt (25-amp) - to maintain constant power delivery without unwanted ripple, noise, and transient spikes during ECU flashing, reprogramming, and diagnostic testing.\u003c\/li\u003e\n\u003cli\u003eDesigned for pros who need absolute performance and uncompromising functionality. Featuring ultra-flexible silicone cabling - down to -40ºC - with protective nylon breaded shielding for maximum protection against abrasion.\u003c\/li\u003e\n\u003cli\u003eA multi-voltage charger - 6-volt (50-amps), 12-volt (50-amps), and 24-volt (25-amps) - for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003eCE\/UKCA\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e400\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e222\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e255\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e5.02\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nntroducing the all-new GENIUSPRO25, a 6-volt,12-volt, and 24-volt fully-automatic professional smart charger, maintainer, power supply, and battery-desulfator with temperature compensation rated at 25-amps for all types of automotive, marine, and deep-cycle batteries.","brand":"NOCO","offers":[{"title":"1","offer_id":56342255993212,"sku":"GENIUSPRO25","price":635.51,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUSPRO25.jpg?v=1771540940"},{"product_id":"noco-geniuspro50-pro-battery-charger-50a","title":"Professional 50a Workshop Charger","description":"\u003cp\u003eThe Professional 50a Workshop Charger is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Its catalogue specification records CE\/UKCA technical info. Use Noco reference GENIUSPRO50 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAutomatically detects battery sulfation and acid stratification to restore lost battery performance for stronger engine starts and extended battery life. Plus, cutting-edge battery repair modes for 6-volt, 12-volt, and 24-volt batteries.\u003c\/li\u003e\n\u003cli\u003eDetects batteries as low as 1-volt. Or use the all-new force mode that allows you to manually begin charging dead batteries down to zero volts.\u003c\/li\u003e\n\u003cli\u003eAn integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates to maximize battery life and enable fast charging.\u003c\/li\u003e\n\u003cli\u003eA dual-voltage power supply - 12-volt (50-amp) and 24-volt (25-amp) - to maintain constant power delivery without unwanted ripple, noise, and transient spikes during ECU flashing, reprogramming, and diagnostic testing.\u003c\/li\u003e\n\u003cli\u003eDesigned for pros who need absolute performance and uncompromising functionality. Featuring ultra-flexible silicone cabling - down to -40ºC - with protective nylon breaded shielding for maximum protection against abrasion.\u003c\/li\u003e\n\u003cli\u003eA multi-voltage charger - 6-volt (50-amps), 12-volt (50-amps), and 24-volt (25-amps) - for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003eCE\/UKCA\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e245\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e285\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e460\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e7.7292\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nIntroducing the all-new GENIUSPRO50, a 6-volt,12-volt, and 24-volt fully-automatic professional smart charger, maintainer, power supply, and battery-desulfator with temperature compensation rated at 50-amps for all types of automotive, marine, and deep-cycle batteries.","brand":"NOCO","offers":[{"title":"1","offer_id":56342256124284,"sku":"GENIUSPRO50","price":923.8,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUSPRO50.jpg?v=1771540942"},{"product_id":"gys-025967-gysflash-101-24-h7","title":"GYSflash 101.24 Battery Support Unit 5M Cables","description":"\u003cp\u003eThe GYSflash 101.24 Battery Support Unit 5M Cables is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Gys reference 025967 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFlexible Voltage, the charger operates with a supply voltage between 85 and 265 V\u003c\/li\u003e\n\u003cli\u003eExtends the life and performance of Lead (gel, AGM, liquid, calcium, etc.) and Lithium (LFP) batteries.\u003c\/li\u003e\n\u003cli\u003eConnect additional modules (printer, barcode reader, etc.)\u003c\/li\u003e\n\u003cli\u003eAdd, delete or modify charging modes and profiles via USB\u003c\/li\u003e\n\u003cli\u003eTemperature sensor to prevent internal electronics overheating.\u003c\/li\u003e\n\u003cli\u003eProtects the on-board electronics of the vehicle: short circuit, reverse polarity and overload protection. Spark prevention system.\u003c\/li\u003e\n\u003cli\u003eTester mode\u003c\/li\u003e\n\u003cli\u003eBattery change mode\u003c\/li\u003e\n\u003cli\u003eCharging mode\u003c\/li\u003e\n\u003cli\u003ePower supply mode\u003c\/li\u003e\n\u003cli\u003eShowroom mode\u003c\/li\u003e\n\u003cli\u003eConnectivity (CNT) - Fully updatable and futureproof\u003c\/li\u003e\n\u003cli\u003eHigh-power multifunction stabilized power supply for lead-acid batteries (sealed, liquid, AGM, etc.) or Lithium (LiFePO4)\u003c\/li\u003e\n\u003cli\u003e100A Battery support unit\u003c\/li\u003e\n\u003cli\u003eTesla 16V capable (12\/16\/24V)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003ecert025967.pdf\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e405\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e220\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e385\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e10.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GYSFLASH 101.24 CNT FV is a 100 A high power CONNECTED charger with inverter technology. It allows to keep a 6 V, 12 V, 16 V and 24 V lead or lithium battery (Lithium-ion «standard» + Lithium-iron Phosphate) at a perfectly stabilized voltage during the diagnostic phases. It will deliver the best charging cycle recommended for the maintenance of the most advanced vehicles on the market. Its USB connectivity makes it 100% customizable.","brand":"GYS","offers":[{"title":"1","offer_id":56342263071100,"sku":"025967","price":1210.68,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/025967.jpg?v=1771519304"},{"product_id":"bosch-0687000044-bat-6120-battery-support-unit","title":"BAT 6120 Battery Support Unit","description":"\u003cp\u003eThe BAT 6120 Battery Support Unit is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Bosch reference 0687000044 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eEasy access to BAT 6120 Help Center web page through QR code displayed on the screen\u003c\/li\u003e\n\u003cli\u003eEasy to use large 4 colour backlight LCD display including wall mount mode\u003c\/li\u003e\n\u003cli\u003eFits underneath a car in show room\u003c\/li\u003e\n\u003cli\u003eDesk, floor or wall operations possible\u003c\/li\u003e\n\u003cli\u003eFlexible operation modes to fulfill customer needs\u003c\/li\u003e\n\u003cli\u003eMaximum power output: up to 1750 W\u003c\/li\u003e\n\u003cli\u003eInterface available in 26 languages\u003c\/li\u003e\n\u003cli\u003e12 V Lead Acid Battery Charge. Charging Diagnosis \/ 12 V Lithium Battery Charge, Wake Up\u003c\/li\u003e\n\u003cli\u003eSupports Flooded\/AGM\/EFB\/GEL\/Lithium (LFP) Batteries\u003c\/li\u003e\n\u003cli\u003eSupports 120 A DC Continuous Output (AC120 V - 240 V, 25 degree Celcius)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eDimensions (W x H x D): 329 x 116 x 433 mm\u003c\/li\u003e \u003cli\u003eProtection type (DIN 40050): IP 20 D \u003c\/li\u003e \u003cli\u003eBattery nominal voltage: 12 V\u003c\/li\u003e \u003cli\u003eMain voltage: 220 - 240 V, 50\/60 Hz\u003c\/li\u003e \u003cli\u003eFunction temperature range: 0 – 40 degree(C)\u003c\/li\u003e \u003cli\u003e Max. 120 A continuous current\u003c\/li\u003e \u003cli\u003eFloating-mode operation: 12.0 V - 13.2 V adjustable, default 13.5 V\u003c\/li\u003e \u003cli\u003eBackup mode: 12.0 V - 13.2 V adjustable, default 12.6 V \/ 10 A - 30 A adjustable power limit, default 20 A\u003c\/li\u003e \u003cli\u003eCharging characteristic: up to 120 Amperes continuous. Battery types: UNI, WET, EFB, AGM, VRLA\/GEL, LFP (LiFePO4)\u003c\/li\u003e \u003cli\u003eWeight (without charging and power cable): 8.5 kg\u003c\/li\u003e \u003cli\u003ePower input :120 - 240 V AC\u003c\/li\u003e \u003cli\u003eCross-section charging cable: 25 mm sq.\u003c\/li\u003e \u003cli\u003eLength of the charging cable: 3 m (twin cable)\u003c\/li\u003e \u003cli\u003eMax. Charge current intensity 12V: 120 A\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e559\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e329\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e439\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e12.579\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe Bosch BAT 6120 is a future-proof, professional, two-in-one battery support solution for automotive workshops. Functioning dependably as a smart and fast battery charger, for lead acid and lithium batteries, or as a 120 A continuous power supply.","brand":"BOSCH","offers":[{"title":"1","offer_id":56342263824764,"sku":"0687000044","price":1475.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/0687000044.jpg?v=1771519685"},{"product_id":"maypole-713a-metal-battery-charger-8a-12v","title":"Metal Battery Charger - 8A - 12V","description":"\u003cul\u003e\n\u003cli\u003eOverload, reverse polarity and short circuit protection\u003c\/li\u003e\n\u003cli\u003eFully insulated battery clips\u003c\/li\u003e\n\u003cli\u003eFor all low maintenance and maintenance free 12V\/24V lead acid batteries of 30-180Ah capacity\u003c\/li\u003e\n\u003cli\u003eRobust steel cast with carrying handle\u003c\/li\u003e\n\u003cli\u003eAmmeter clearly shows charging rate\u003c\/li\u003e\n\u003cli\u003eSuitable for cars, vans, tractors, commercial vehicles and leisure batteries\u003c\/li\u003e\n\u003cli\u003eFast charge and boost functions\u003c\/li\u003e\n\u003cli\u003eKey Features:\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e280\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e175\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e210\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e4.145\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nWhether your car battery struggles because of the cold, lack of use or even because you've accidentally left your lights on, battery chargers are a great way to get your battery back up and running and maintaining it.\u003cp\u003eThis 12A battery charger is a fast and efficient way of getting your vehicle's battery back up and working. Connect the fully insulated metal clips to the battery and leave until fully charged. The charger comes in a robust steel case, has a carrying handle and offers protection against reverse polarity and overloading. It is suitable for applications including cars, vans and tractors with 12V or 24V lead-acid batteries. It also has an ammeter that clearly displays the charging current on the front of the charger.\u003c\/p\u003e\u003cp\u003eMaypole was established over 40 years ago beginning with the manufacturing of trailer lighting boards and since then has grown into one of the premier companies in Europe offering ranges of products for the Towing, Trailer, Automotive Aftermarket, Leisure, Agriculture and Marine markets. The company is proud that it is still an independent and family owned business, with total focus on Customers, Quality and Service.\u003c\/p\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56352055820668,"sku":"713A","price":55.89,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/713A.jpg?v=1771527439"},{"product_id":"maypole-716-battery-charger-metal-12a-12-24v","title":"Metal Battery Charger - 12A - 12V\/24V","description":"\u003cul\u003e\n\u003cli\u003eOverload, reverse polarity and short circuit protection\u003c\/li\u003e\n\u003cli\u003eFully insulated battery clips\u003c\/li\u003e\n\u003cli\u003eFor all low maintenance and maintenance free 12V\/24V lead acid batteries of 30-180Ah capacity\u003c\/li\u003e\n\u003cli\u003eRobust steel cast with carrying handle\u003c\/li\u003e\n\u003cli\u003eAmmeter clearly shows charging rate\u003c\/li\u003e\n\u003cli\u003eSuitable for cars, vans, tractors, commercial vehicles and leisure batteries\u003c\/li\u003e\n\u003cli\u003eFast charge and boost functions\u003c\/li\u003e\n\u003cli\u003eKey Features:\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e315\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e190\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e235\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e6.447\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nWhether your car battery struggles because of the cold, lack of use or even because you've accidentally left your lights on, battery chargers are a great way to get your battery back up and running and maintaining it.\u003cp\u003eThis 12A battery charger is a fast and efficient way of getting your vehicle's battery back up and working. Connect the fully insulated metal clips to the battery and then choose between a 12V and 24V charge and leave until fully charged. It has a boost option for faster charging and an ammeter that clearly displays the charging current. The charger comes in a robust steel case, has a carrying handle and offers protection against reverse polarity and overloading. It is suitable for applications including cars, vans and tractors with 12V or 24V lead-acid batteries.\u003c\/p\u003e\u003cp\u003eMaypole was established over 40 years ago beginning with the manufacturing of trailer lighting boards and since then has grown into one of the premier companies in Europe offering ranges of products for the Towing, Trailer, Automotive Aftermarket, Leisure, Agriculture and Marine markets. The company is proud that it is still an independent and family owned business, with total focus on Customers, Quality and Service.\u003c\/p\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56352056050044,"sku":"716","price":65.98,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/716.jpg?v=1771527454"},{"product_id":"maypole-730-battery-charger-metal-20a-12-24v","title":"Metal Battery Charger - 20A - 12V\/24V","description":"\u003cul\u003e\n\u003cli\u003eOverload, reverse polarity and short circuit protection\u003c\/li\u003e\n\u003cli\u003eFully insulated battery clips\u003c\/li\u003e\n\u003cli\u003eFor all low maintenance and maintenance free 12V\/24V lead acid batteries of 30-180Ah capacity\u003c\/li\u003e\n\u003cli\u003eRobust steel cast with carrying handle\u003c\/li\u003e\n\u003cli\u003eAmmeter clearly shows charging rate\u003c\/li\u003e\n\u003cli\u003eSuitable for cars, vans, tractors, commercial vehicles and leisure batteries\u003c\/li\u003e\n\u003cli\u003eFast charge and boost functions\u003c\/li\u003e\n\u003cli\u003eKey Features:\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e390\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e215\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e260\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e11.589\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nWhether your car battery struggles because of the cold, lack of use or even because you've accidentally left your lights on, battery chargers are a great way to get your battery back up and running and maintaining it.\u003cp\u003eThis 20A battery charger is a fast and efficient way of getting your vehicle's battery back up and working. Connect the fully insulated metal clips to the battery and then choose between a 12V and 24V charge and leave until fully charged. It has 'fast charge' and 'boost' functions for speedy charges and an ammeter that clearly displays the charging current. The charger comes in a robust steel case, has a carrying handle and offers protection against reverse polarity and overloading. It is suitable for applications including cars, vans and tractors with 12V or 24V lead-acid batteries.\u003c\/p\u003e\u003cp\u003eMaypole was established over 40 years ago beginning with the manufacturing of trailer lighting boards and since then has grown into one of the premier companies in Europe offering ranges of products for the Towing, Trailer, Automotive Aftermarket, Leisure, Agriculture and Marine markets. The company is proud that it is still an independent and family owned business, with total focus on Customers, Quality and Service.\u003c\/p\u003e","brand":"MAYPOLE","offers":[{"title":"1","offer_id":56352056344956,"sku":"730","price":104.32,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/730.jpg?v=1771527517"},{"product_id":"batium-15-24-smart-charger","title":"Batium 15.24 Smart Charger","description":"\u003cp\u003eThe Batium 15.24 Smart Charger is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Batium 15.24 Smart Charger enhanced description. Use Gys reference 024588 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003ecert024588 (1).pdf\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEnhanced Description\u003c\/th\u003e\n\u003ctd\u003eBatium 15.24 Smart Charger\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInfo\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eSafe for all types of Lead Acid batteries even when the type is unknown\u003c\/li\u003e \u003cli\u003eThe Batium 15.24 will not deliver current if there is no battery detected (no voltage in the clamps).\u003c\/li\u003e \u003cli\u003eAnti-spark feature which prevents sparks whilst connecting the Gysflash to the battery.\u003c\/li\u003e \u003cli\u003eProtected against short-circuits, polarity reversals and vehicle start\u003c\/li\u003e \u003cli\u003eSOS recovery GO \u0026gt;0.5V\u003c\/li\u003e \u003cli\u003eThe BATIUM range is a microprocessor-controlled smart charger, it constantly analyses the battery's condition and regulates the charging process accordingly.\u003c\/li\u003e \u003cli\u003eFull charge and 100% charge level maintenance.\u003c\/li\u003e \u003cli\u003eCharges 50% faster than a traditional charger.\u003c\/li\u003e \u003cli\u003eCan be used on batteries for motorcycles, collector's vehicles, light vehicles, vans, agricultural machinery, public works vehicles, heavy goods vehicles and buses from 35 to 225 Ah.\u003c\/li\u003e \u003cli\u003eProtection of on-board electronics.\u003c\/li\u003e \u003cli\u003eRecovery of heavily discharged batteries (from 2 V).\u003c\/li\u003e \u003cli\u003eAutomatic charger for all types of lead-acid batteries (Gel, liquid, AGM, VRLA) 6\/12\/24V\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e210\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e143\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e362\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e7.1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n\u003cul\u003e\n\u003cli\u003eAutomatic charger for all types of lead-acid batteries (Gel, liquid, AGM, VRLA) 6\/12\/24V\u003c\/li\u003e\n\u003cli\u003eRecovery of heavily discharged batteries (from 2 V).\u003c\/li\u003e\n\u003cli\u003eProtection of on-board electronics.\u003c\/li\u003e\n\u003cli\u003eCan be used on batteries for motorcycles, collector's vehicles, light vehicles, vans, agricultural machinery, public works vehicles, heavy goods vehicles and buses from 35 to 225 Ah.\u003c\/li\u003e\n\u003cli\u003eCharges 50% faster than a traditional charger.\u003c\/li\u003e\n\u003c\/ul\u003e\n\nAutomatic charger for all types of lead-acid batteries (gel, liquid, AGM, VRLA) 6\/12\/24 V. Can be used for batteries on motorcycles, collector's vehicles, light vehicles, vans, agricultural machinery, public works vehicles, heavy goods vehicles and buses from 35 to 225 Ah.","brand":"GYS","offers":[{"title":"Default Title","offer_id":56354405187964,"sku":"024588","price":217.12,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GYS_024588_batium-15-24-smart-charger.jpg?v=1770825337"},{"product_id":"gysflash-101-24-battery-support-unit-5m-cables","title":"GYSflash 101.24 Battery Support Unit 5M Cables","description":"\u003cp\u003eThe GYSflash 101.24 Battery Support Unit 5M Cables is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records GYSflash 101.24 Battery Support Unit 5M Cables enhanced description. Use Gys reference 025967 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003ecert025967.pdf\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEnhanced Description\u003c\/th\u003e\n\u003ctd\u003eGYSflash 101.24 Battery Support Unit 5M Cables\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInfo\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eFlexible Voltage, the charger operates with a supply voltage between 85 and 265 V\u003c\/li\u003e \u003cli\u003eExtends the life and performance of Lead (gel, AGM, liquid, calcium, etc.) and Lithium (LFP) batteries.\u003c\/li\u003e \u003cli\u003eConnect additional modules (printer, barcode reader, etc.)\u003c\/li\u003e \u003cli\u003eAdd, delete or modify charging modes and profiles via USB\u003c\/li\u003e \u003cli\u003eTemperature sensor to prevent internal electronics overheating.\u003c\/li\u003e \u003cli\u003eProtects the on-board electronics of the vehicle: short circuit, reverse polarity and overload protection. Spark prevention system.\u003c\/li\u003e \u003cli\u003eTester mode\u003c\/li\u003e \u003cli\u003eBattery change mode\u003c\/li\u003e \u003cli\u003eCharging mode\u003c\/li\u003e \u003cli\u003ePower supply mode\u003c\/li\u003e \u003cli\u003eShowroom mode\u003c\/li\u003e \u003cli\u003eConnectivity (CNT) - Fully updatable and futureproof\u003c\/li\u003e \u003cli\u003eHigh-power multifunction stabilized power supply for lead-acid batteries (sealed, liquid, AGM, etc.) or Lithium (LiFePO4)\u003c\/li\u003e \u003cli\u003e100A Battery support unit\u003c\/li\u003e \u003cli\u003eTesla 16V capable (12\/16\/24V)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e405\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e220\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e385\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e10.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n\u003cul\u003e\n\u003cli\u003eTesla 16V capable (12\/16\/24V)\u003c\/li\u003e\n\u003cli\u003e100A Battery support unit\u003c\/li\u003e\n\u003cli\u003eHigh-power multifunction stabilized power supply for lead-acid batteries (sealed, liquid, AGM, etc.) or Lithium (LiFePO4)\u003c\/li\u003e\n\u003cli\u003eConnectivity (CNT) - Fully updatable and futureproof\u003c\/li\u003e\n\u003cli\u003eShowroom mode\u003c\/li\u003e\n\u003c\/ul\u003e\n\nThe GYSFLASH 101.24 CNT FV is a 100 A high power CONNECTED charger with inverter technology. It allows to keep a 6 V, 12 V, 16 V and 24 V lead or lithium battery (Lithium-ion «standard» + Lithium-iron Phosphate) at a perfectly stabilized voltage during the diagnostic phases. It will deliver the best charging cycle recommended for the maintenance of the most advanced vehicles on the market. Its USB connectivity makes it 100% customizable.","brand":"GYS","offers":[{"title":"Default Title","offer_id":56354406105468,"sku":"025967","price":1210.68,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GYS_025967_gysflash-101-24-battery-support-unit-5m-cables.jpg?v=1770825343"},{"product_id":"gysflash-100-12-battery-support-unit-5m-cables","title":"GYSflash 100.12 Battery Support Unit 5M Cables","description":"\u003cp\u003eThe GYSflash 100.12 Battery Support Unit 5M Cables is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Gys reference 029002 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLockable, prevents any risk of accidental or improper operation\u003c\/li\u003e\n\u003cli\u003eExtends the life and performance of Lead (gel, AGM, liquid, calcium, etc.) and Lithium (LFP) batteries.\u003c\/li\u003e\n\u003cli\u003eEasy charging profile for simplified recharging of all lead-acid and lithium batteries.\u003c\/li\u003e\n\u003cli\u003eNo supervision needed\u003c\/li\u003e\n\u003cli\u003eTemperature sensor to prevent internal electronics overheating.\u003c\/li\u003e\n\u003cli\u003eProtects the on-board electronics of the vehicle: short circuit, reverse polarity and overload protection. Spark prevention system.\u003c\/li\u003e\n\u003cli\u003eSOS function - Recovers batteries from \u0026gt;2V\u003c\/li\u003e\n\u003cli\u003eCompact design - fits comfortably under showroom vehicles\u003c\/li\u003e\n\u003cli\u003eHigh efficiency\u003c\/li\u003e\n\u003cli\u003ePower supply mode\u003c\/li\u003e\n\u003cli\u003eShowroom mode\u003c\/li\u003e\n\u003cli\u003eBattery change mode\u003c\/li\u003e\n\u003cli\u003eCharging mode\u003c\/li\u003e\n\u003cli\u003eDiagnostic support mode\u003c\/li\u003e\n\u003cli\u003eHigh-power multifunction stabilized power supply for lead-acid batteries (sealed, liquid, AGM, etc.) or Lithium (LiFePO4)\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\u003cli\u003ecert029002 (1).pdf\u003c\/li\u003e\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e305\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e250\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e405\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e8.38\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GYSFLASH 100.12 HF is a high-performance 100 A charger with inverter technology. Designed to keep a 12 V lead-acid or lithium battery at a perfectly stable voltage, it preserves the health of a vehicle’s battery during showroom demonstrations. It also delivers the best charging cycle recommended for the maintenance of the most advanced vehicles on the market.","brand":"GYS","offers":[{"title":"Default Title","offer_id":56354407383420,"sku":"029002","price":906.65,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GYS_029002_gysflash-100-12-battery-support-unit-5m-cables.jpg?v=1770825371"},{"product_id":"bat-6120-battery-support-unit","title":"BAT 6120 Battery Support Unit","description":"\u003cp\u003eThe BAT 6120 Battery Support Unit is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records BAT 6120 Battery Support Unit enhanced description. Use Bosch reference 0687000044 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eDimensions (W x H x D): 329 x 116 x 433 mm\u003c\/li\u003e \u003cli\u003eProtection type (DIN 40050): IP 20 D \u003c\/li\u003e \u003cli\u003eBattery nominal voltage: 12 V\u003c\/li\u003e \u003cli\u003eMain voltage: 220 - 240 V, 50\/60 Hz\u003c\/li\u003e \u003cli\u003eFunction temperature range: 0 – 40 degree(C)\u003c\/li\u003e \u003cli\u003e Max. 120 A continuous current\u003c\/li\u003e \u003cli\u003eFloating-mode operation: 12.0 V - 13.2 V adjustable, default 13.5 V\u003c\/li\u003e \u003cli\u003eBackup mode: 12.0 V - 13.2 V adjustable, default 12.6 V \/ 10 A - 30 A adjustable power limit, default 20 A\u003c\/li\u003e \u003cli\u003eCharging characteristic: up to 120 Amperes continuous. Battery types: UNI, WET, EFB, AGM, VRLA\/GEL, LFP (LiFePO4)\u003c\/li\u003e \u003cli\u003eWeight (without charging and power cable): 8.5 kg\u003c\/li\u003e \u003cli\u003ePower input :120 - 240 V AC\u003c\/li\u003e \u003cli\u003eCross-section charging cable: 25 mm sq.\u003c\/li\u003e \u003cli\u003eLength of the charging cable: 3 m (twin cable)\u003c\/li\u003e \u003cli\u003eMax. Charge current intensity 12V: 120 A\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEnhanced Description\u003c\/th\u003e\n\u003ctd\u003eBAT 6120 Battery Support Unit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInfo\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eEasy access to BAT 6120 Help Center web page through QR code displayed on the screen\u003c\/li\u003e \u003cli\u003eEasy to use large 4 colour backlight LCD display including wall mount mode\u003c\/li\u003e \u003cli\u003eFits underneath a car in show room\u003c\/li\u003e \u003cli\u003eDesk, floor or wall operations possible\u003c\/li\u003e \u003cli\u003eFlexible operation modes to fulfill customer needs\u003c\/li\u003e \u003cli\u003eMaximum power output: up to 1750 W\u003c\/li\u003e \u003cli\u003eInterface available in 26 languages\u003c\/li\u003e \u003cli\u003e12 V Lead Acid Battery Charge. Charging Diagnosis \/ 12 V Lithium Battery Charge, Wake Up\u003c\/li\u003e \u003cli\u003eSupports Flooded\/AGM\/EFB\/GEL\/Lithium (LFP) Batteries\u003c\/li\u003e \u003cli\u003eSupports 120 A DC Continuous Output (AC120 V - 240 V, 25 degree Celcius)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e559\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e329\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e439\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e12.579\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\n\u003cul\u003e\n\u003cli\u003eSupports 120 A DC Continuous Output (AC120 V - 240 V, 25 degree Celcius)\u003c\/li\u003e\n\u003cli\u003eSupports Flooded\/AGM\/EFB\/GEL\/Lithium (LFP) Batteries\u003c\/li\u003e\n\u003cli\u003e12 V Lead Acid Battery Charge. Charging Diagnosis \/ 12 V Lithium Battery Charge, Wake Up\u003c\/li\u003e\n\u003cli\u003eInterface available in 26 languages\u003c\/li\u003e\n\u003cli\u003eMaximum power output: up to 1750 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\nThe Bosch BAT 6120 is a future-proof, professional, two-in-one battery support solution for automotive workshops. Functioning dependably as a smart and fast battery charger, for lead acid and lithium batteries, or as a 120 A continuous power supply.","brand":"BOSCH","offers":[{"title":"Default Title","offer_id":56354414952828,"sku":"0687000044","price":1475.69,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/BOSCH_0687000044_bat-6120-battery-support-unit.jpg?v=1770825551"},{"product_id":"starter-charger-50a","title":"Starter Charger - 50A","description":"\u003cp\u003eThe Starter Charger - 50A is a catalogued automotive or workshop product that is identified by the product-specific specification recorded for this catalogue entry. Its catalogue specification records Boosting Current 0V = 300A Maximum Charging Current = 50A Battery Capacities = 120-750Ah (12V) technical info. Use Maypole reference 725 when cross-checking the part. Compare the manufacturer reference, dimensions, supplied items and application notes below before ordering; appearance alone is not a reliable way to confirm compatibility.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eNot compatible with household plugs\/circuits. These chargers require 32 Amp current as opposed to 13Amp which is provided in household plugs\u003c\/li\u003e\n\u003cli\u003eDimensions - 670x385x300mm\u003c\/li\u003e\n\u003cli\u003eSuitable for applications including cars, commercial vehicles, vans and tractors with 12V or 24V lead acid batteries\u003c\/li\u003e\n\u003cli\u003eFull colour display box\u003c\/li\u003e\n\u003cli\u003e12V\/24V\u003c\/li\u003e\n\u003cli\u003eEasy to manoeuvre with wheels and moving handle\u003c\/li\u003e\n\u003cli\u003eRobust steel case\u003c\/li\u003e\n\u003cli\u003ePortable and robust design\u003c\/li\u003e\n\u003cli\u003eFully insulated metal clips\u003c\/li\u003e\n\u003cli\u003eTÜV approved\u003c\/li\u003e\n\u003cli\u003eReverse polarity and overload protection\u003c\/li\u003e\n\u003cli\u003eAmmeter to show charging current\u003c\/li\u003e\n\u003cli\u003eKey Features:\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eBoosting Current 0V = 300A\u003c\/li\u003e \u003cli\u003eMaximum Charging Current = 50A\u003c\/li\u003e \u003cli\u003eBattery Capacities = 120-750Ah (12V)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e680\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e300\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e385\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e27.76\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"Default Title","offer_id":56385919123836,"sku":"725","price":224.26,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/725.jpg?v=1771527500"},{"product_id":"metal-battery-charger-30a-12v-24v","title":"Metal Battery Charger - 30A - 12V\/24V","description":"\u003cul\u003e\n\u003cli\u003eOverload, reverse polarity and short circuit protection\u003c\/li\u003e\n\u003cli\u003eFully insulated battery clips\u003c\/li\u003e\n\u003cli\u003eFor all low maintenance and maintenance free 12V\/24V lead acid batteries of 30-180Ah capacity\u003c\/li\u003e\n\u003cli\u003eRobust steel cast with carrying handle\u003c\/li\u003e\n\u003cli\u003eAmmeter clearly shows charging rate\u003c\/li\u003e\n\u003cli\u003eSuitable for cars, vans, tractors, commercial vehicles and leisure batteries\u003c\/li\u003e\n\u003cli\u003eFast charge and boost functions\u003c\/li\u003e\n\u003cli\u003eKey Features:\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e405\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e250\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e260\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e14.318\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nWhether your car battery struggles because of the cold, lack of use or even because you've accidentally left your lights on, battery chargers are a great way to get your battery back up and running and maintaining it.\u003cp\u003eThis 30A battery charger is a fast and efficient way of getting your vehicle's battery back up and working. Connect the fully insulated metal clips to the battery and then choose between a 12V and 24V charge and leave until fully charged. It has a 'fast charge' and 'boost' function for speedy charges and an ammeter that clearly displays the charging current. The charger comes in a robust steel case, has a carrying handle and offers protection against reverse polarity and overloading. It is suitable for applications including cars, vans and tractors with 12V or 24V lead-acid batteries.\u003c\/p\u003e\u003cp\u003eMaypole was established over 40 years ago beginning with the manufacturing of trailer lighting boards and since then has grown into one of the premier companies in Europe offering ranges of products for the Towing, Trailer, Automotive Aftermarket, Leisure, Agriculture and Marine markets. The company is proud that it is still an independent and family owned business, with total focus on Customers, Quality and Service.\u003c\/p\u003e","brand":"MAYPOLE","offers":[{"title":"Default Title","offer_id":56385925546364,"sku":"750","price":113.58,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/750.jpg?v=1771527565"},{"product_id":"smart-battery-charger-6v-12v-10a","title":"Smart Battery Charger - 6V \u0026 12V - 10A","description":"\u003cp\u003eThe Smart Battery Charger - 6V \u0026amp; 12V - 10A is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Noco reference GENIUS10UK when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShort-Circuit: Yes | Open-Circuit: Yes | Overheating: Yes | Overcharge: Yes | Spark-Proof: Yes | Reverse Polarity: Yes\u003c\/li\u003e\n\u003cli\u003e3-Year Limited Warranty\u003c\/li\u003e\n\u003cli\u003eThe M6 eyelet clamps have wide clamping range and improved clamping force for higher conductivity.\u003c\/li\u003e\n\u003cli\u003eProvides all-season and all-weather charging for a healthy battery.\u003c\/li\u003e\n\u003cli\u003eCharge safely 24\/7 without any risk of overcharging your batteries, plus additional safety like spark-proof connections, and reverse polarity protection.\u003c\/li\u003e\n\u003cli\u003eAn ultra-compact and high-efficiency design with maximum power density and detailed dynamic battery tracking.\u003c\/li\u003e\n\u003cli\u003eCompatible with all types of vehicles.\u003c\/li\u003e\n\u003cli\u003eAutomatically repairs and reverses battery damage caused by sulfation and acid stratification to restore performance and extend battery life.\u003c\/li\u003e\n\u003cli\u003eCharges dead batteries as low as 0-volts in the new 'Force Mode'.\u003c\/li\u003e\n\u003cli\u003eAlters the charge to eliminate over-charging in hot climates and under-charging in cold climates.\u003c\/li\u003e\n\u003cli\u003eDesigned for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eOperating requirements - Line Voltage: 120V to 240V AC\u003c\/li\u003e \u003cli\u003eFrequency: 50Hz to 60Hz\u003c\/li\u003e \u003cli\u003eOperating Temperature: -4° to 104° F (-20° to 40° C)\u003c\/li\u003e \u003cli\u003eStorage Temperature: -22° to 140° F (-30° to 60° C)\u003c\/li\u003e \u003cli\u003eRelative Humidity: 0 to 95% Non-Condensing\u003c\/li\u003e \u003cli\u003eIP Rating: IP65\u003c\/li\u003e \u003cli\u003eConsumption: 150 Watts (Max)\u003c\/li\u003e \u003cli\u003eEfficiency: 87% (120VAC\/230VAC)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e227\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e114\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e112\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e1.8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GENIUS10UK is an ultra-compact and high efficiency 10-Amp 6-volt and 12-volt battery charger, battery maintainer, and battery desulfator for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries. An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates. Charge dead batteries as low as 1-volt, or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts. The GENIUS10UK is a fully-automatic, worry-free battery chargers for year-round use. Restore your battery by detecting sulfation and acid stratification and restoring lost performance for stronger engine starts and extended battery life. Compatible with all types of vehicles. Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, racing cars, performance cars and more.","brand":"NOCO","offers":[{"title":"Default Title","offer_id":56386305786236,"sku":"GENIUS10UK","price":134.48,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUS10UK.jpg?v=1771540933"},{"product_id":"smart-battery-charger-6v-12v-2a","title":"Smart Battery Charger - 6V\/12V - 2A","description":"\u003cp\u003eThe Smart Battery Charger - 6V\/12V - 2A is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Use Noco reference GENIUS2UK when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eShort-Circuit: Yes | Open-Circuit: Yes | Overheating: Yes | Overcharge: Yes | Spark-Proof: Yes | Reverse Polarity: Yes\u003c\/li\u003e\n\u003cli\u003e3-Year Limited Warranty\u003c\/li\u003e\n\u003cli\u003eThe M6 eyelet clamps have wide clamping range and improved clamping force for higher conductivity.\u003c\/li\u003e\n\u003cli\u003eProvides all-season and all-weather charging for a healthy battery.\u003c\/li\u003e\n\u003cli\u003eCharge safely 24\/7 without any risk of overcharging your batteries, plus additional safety like spark-proof connections, and reverse polarity protection.\u003c\/li\u003e\n\u003cli\u003eAn ultra-compact and high-efficiency design with maximum power density and detailed dynamic battery tracking.\u003c\/li\u003e\n\u003cli\u003eCompatible with all types of vehicles.\u003c\/li\u003e\n\u003cli\u003eAutomatically repairs and reverses battery damage caused by sulfation and acid stratification to restore performance and extend battery life.\u003c\/li\u003e\n\u003cli\u003eCharges dead batteries as low as 0-volts in the new 'Force Mode'.\u003c\/li\u003e\n\u003cli\u003eAlters the charge to eliminate over-charging in hot climates and under-charging in cold climates.\u003c\/li\u003e\n\u003cli\u003eDesigned for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eOperating requirements - Line Voltage: 120V to 240V AC\u003c\/li\u003e \u003cli\u003eFrequency: 50Hz to 60Hz\u003c\/li\u003e \u003cli\u003eOperating Temperature: -4° to 104° F (-20° to 40° C)\u003c\/li\u003e \u003cli\u003eStorage Temperature: -22° to 140° F (-30° to 60° C)\u003c\/li\u003e \u003cli\u003eRelative Humidity: 0 to 95% Non-Condensing\u003c\/li\u003e \u003cli\u003eIP Rating: IP65\u003c\/li\u003e \u003cli\u003eConsumption: 30 Watts (Max)\u003c\/li\u003e \u003cli\u003eEfficiency: 87% (120VAC\/230VAC)\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e178\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e108\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e89\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e0.59\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e\n\nThe GENIUS2UK is an ultra-compact and high efficiency 2-Amp 6-volt and 12-volt battery charger, battery maintainer, and battery desulfator for lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries. An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates. Charge dead batteries as low as 1-volt, or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts. The GENIUS2UK is a fully-automatic, worry-free battery chargers for year-round use. Restore your battery by detecting sulfation and acid stratification and restoring lost performance for stronger engine starts and extended battery life. Compatible with all types of vehicles. Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, classic cars, racing cars and more.","brand":"NOCO","offers":[{"title":"Default Title","offer_id":56386305884540,"sku":"GENIUS2UK","price":57.28,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/GENIUS2UK.jpg?v=1771540938"},{"product_id":"battery-charger-12a-12v-24v-led-automatic","title":"Battery Charger 12A - 12V\/24V - LED Automatic","description":"\u003cp\u003eThe Battery Charger 12A - 12V\/24V - LED Automatic is a battery charging, support or diagnostic product that is designed for the battery voltage and operating mode stated in its product data. Its catalogue specification records Input: 230V AC 50Hz Output: 6v DC 5.1A (EN Rated) 8A Max 12V DC 5.1A (EN Rated) 8A Max technical info. Use Maypole reference MP7112 when cross-checking the part. Confirm the supported battery chemistry, voltage, current range, lead connections and operating instructions before use; provide ventilation and observe battery polarity and eye-protection precautions.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for low maintenance and maintenance free 12V lead acid \u0026amp; AGM batteries of 20Ah to 100Ah capacity only\u003c\/li\u003e\n\u003cli\u003eManufactured to European electrical safety standards\u003c\/li\u003e\n\u003cli\u003e1.7m leads with inline fuse protection and fully insulated crocodile clips\u003c\/li\u003e\n\u003cli\u003eOvercharge, short \u0026amp; reverse polarity protection\u003c\/li\u003e\n\u003cli\u003eCompact robust case with integral handle\u003c\/li\u003e\n\u003cli\u003eLED indicators showing charging progress\u003c\/li\u003e\n\u003cli\u003eSuitable for Start\/Stop vehicles\u003c\/li\u003e\n\u003cli\u003eFully automatic - easy to use and safe\u003c\/li\u003e\n\u003cli\u003eSuitable for lead acid \u0026amp; AGM batteries up to 1.8lt\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"specs\"\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eTechnical Info\u003c\/th\u003e\n\u003ctd\u003e\u003cul\u003e\n\u003cli\u003eInput: 230V AC 50Hz\u003c\/li\u003e \u003cli\u003eOutput: 6v DC 5.1A (EN Rated) 8A Max\u003c\/li\u003e \u003cli\u003e12V DC 5.1A (EN Rated) 8A Max\u003c\/li\u003e\n\u003c\/ul\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e195\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e265\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e125\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e4.12\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003c\/div\u003e","brand":"MAYPOLE","offers":[{"title":"Default Title","offer_id":56386349793660,"sku":"MP7112","price":42.62,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0912\/8407\/8972\/files\/MP7112.jpg?v=1771543276"}],"url":"https:\/\/automotopart.co.uk\/collections\/p_battery-charger.oembed?page=2","provider":"AutoMotoPart","version":"1.0","type":"link"}