2 Products
Your Current Vehicle
Or
Select Your Vehicle
How coil springs support and control a vehicle
A suspension spring carries the sprung mass of the body, powertrain, passengers and load while allowing controlled wheel travel. As the wheel rises, the steel bar forming the helix twists. That elastic deformation stores energy; extension returns it. The damper converts unwanted oscillation into heat, while anti-roll bars redistribute load between sides during cornering.
Ride height is the equilibrium between applied load and spring force. It affects suspension geometry, driveshaft angles, aerodynamic attitude, lighting aim and available bump and rebound travel. This is why a spring that physically fits can still be technically wrong.
Spring behaviour step by step
- Vehicle mass compresses each spring from its free length to its installed height.
- A road input moves the wheel and changes spring deflection.
- The spring rate determines the additional force produced for each increment of travel.
- The damper limits the speed of compression and rebound.
- Bump stops progressively protect the suspension near its travel limit.
- Seats and isolators locate the coil and prevent direct metal contact where designed.
- Geometry returns towards its normal position when the disturbance and stored energy subside.
Rate, travel and ride quality
Spring rate depends principally on wire diameter, mean coil diameter, active coil count, material and geometry. A small change in wire diameter can have a large effect. Free length alone does not define ride height because two springs of different rates may settle differently under the same load.
- Constant-rate springs: provide broadly linear force over their working range.
- Progressive springs: increase effective rate as selected coils close or geometry changes.
- Side-load springs: deliberately create a lateral force to reduce strut friction in certain designs.
- Miniblock springs: use shaped wire and compact ends to save space and vary response.
- Load-compensating springs: are calibrated for a particular rear axle or equipment package.
Common suspension applications
| Arrangement | Spring position | Service considerations |
|---|---|---|
| MacPherson strut | Coil surrounds the damper and turns with steering. | Top bearing, spring seat orientation and safe compression are critical. |
| Double wishbone | Spring may sit between arm and body or around a separate damper. | Control-arm position and stored energy remain significant after damper removal. |
| Multi-link rear | Separate barrel or pigtail spring often bears on an arm. | Match left/right seating, isolators and ride-height sensor links. |
| Torsion-beam rear | Separate springs sit near the trailing arms. | Support the beam and protect brake hoses before lowering it. |
| Coil-over damper | Spring is concentric with a serviceable or sealed damper unit. | Platform position, preload and locking rings must follow the approved setup. |
| Auxiliary or helper spring | Additional element operates through part of the travel. | It must complement, not mask failure of, the primary suspension. |
Materials and manufacturing technology
Automotive coil springs are made from high-strength spring steel selected for fatigue resistance, toughness and controlled hardenability. Bar is formed hot or cold according to size and process, heat-treated, shot-peened to create beneficial surface stress, preset to stabilise dimensions and coated against corrosion. Quality depends on the entire process; a colour coating alone says little about fatigue life.
Modern tapered or variable-section wire allows mass reduction and progressive behaviour. Computer-controlled forming improves end geometry, while detailed vehicle modelling lets engineers tune ride and handling without making every coil equally active.
Spring forms and identification
| Feature | Why it varies | What to compare |
|---|---|---|
| Free length | Works with rate and installed load to establish height. | Part data, not a casual measurement of a tired spring. |
| Wire diameter | Strongly influences stiffness and stress. | Measure only where wire is constant and coating is intact. |
| Coil diameter | Controls packaging and rate. | Check clearance to damper, tyre and body. |
| End form | Must mate with shaped upper and lower seats. | Pigtail, tangential, squared or ground end and clocking. |
| Colour marks | Production identification for a load/rate group. | Use as supporting evidence alongside OE references. |
| Left/right designation | Some vehicles compensate for asymmetric packaging or load. | Never assume axle springs are interchangeable side to side. |
Related components
Spring seats and isolators
Stamped or cast seats locate the end coil. Rubber pads suppress noise and protect coatings, but they also affect installed height. A torn pad can trap abrasive dirt or allow the spring to rotate out of position.
Top mounts and bearings
On a strut, the upper mount transfers suspension force into the body and the bearing permits steering rotation. Binding can wind the spring and release it with a knock. Cracked rubber changes alignment and load paths.
Dampers, bump stops and gaiters
A weak damper permits repeated cycling that worsens control and fatigue loading. The bump stop is an active secondary spring near full compression, while the gaiter protects the piston rod. These parts should be assessed whenever access overlaps.
Load limits and vehicle specification
The spring must suit permitted axle weight, not merely the vehicle's empty mass. Tow bars, LPG tanks, wheelchair conversions, roof equipment and permanent tools can change real loading. Up-rating springs does not increase the legal axle, tyre or gross vehicle limits printed by the manufacturer.
| Vehicle detail | Why it matters | Evidence |
|---|---|---|
| Engine and gearbox | Front axle mass changes spring calibration. | VIN, engine code and transmission type. |
| Body style | Estate, saloon, convertible and van structures carry different mass. | Exact derivative and number of doors. |
| Wheelbase | Commercial variants distribute load differently. | Manufacturer model code or measured specification. |
| Sports suspension | Ride height, rate and damper travel may all differ. | Option codes and original equipment data. |
| Self-levelling equipment | Hydraulic or air assistance changes the spring requirement. | Physical system inspection and build specification. |
| Axle-load class | Visually identical models may use different spring groups. | VIN plate and catalogue application notes. |
Wear, corrosion and inspection
Springs undergo millions of stress cycles. Stone chips expose steel; salt and moisture then create pits that concentrate stress. Fractures commonly start near an end coil where dirt collects and movement frets the coating. A broken tip may remain hidden in the seat.
- Compare ride height on level ground with tyre pressures and loading equalised.
- Raise and support the vehicle using approved points, allowing the suspension position specified for inspection.
- Examine the complete circumference of each coil, especially inside the lower seat.
- Look for missing ends, fresh bright fracture faces, deep pitting and coils rubbing together.
- Check pads, mounts, damper leakage, bump stops, hoses and wiring nearby.
- Confirm the spring is correctly clocked and retained at full rebound.
- Investigate tyre contact, shiny body marks or mismatched axle height before road use.
Fault symptoms and urgency
| Symptom | Possible cause | Action |
|---|---|---|
| One corner low | Broken or sagged spring, damaged seat or unequal load. | Inspect promptly and avoid heavy loading. |
| Metallic knock | Fractured end, displaced spring, worn mount or binding bearing. | Check before continued use. |
| Tyre rubbing | Loss of height, wrong spring or displaced component. | Stop if the tyre is being damaged. |
| Steering pull | Unequal height or geometry, though tyres and brakes can also cause it. | Diagnose suspension and alignment. |
| Repeated bottoming | Weak/wrong springs, failed bump stops, overload or poor damping. | Reduce load and inspect the complete system. |
| Visible sharp broken end | Fatigue fracture and corrosion. | Do not drive where tyre or brake damage is possible. |
Safe replacement and common mistakes
A compressed road spring can contain enough energy to cause fatal injury. Use a compressor approved for the spring shape and load, with jaws fully engaged and positioned as its instructions require. Some suspension designs need specialist fixtures or controlled arm support instead of a generic external compressor.
- Do not heat, cut or weld a road spring.
- Do not mix different makes or specifications across one axle.
- Do not grip active coils with tools that damage the protective surface.
- Do not point a compressed strut towards anyone.
- Do not reuse damaged self-locking nuts or ignore specified torque-angle fasteners.
- Do not tighten bonded rubber bushes at full droop unless the procedure says so.
- Do not lower a suspension arm without protecting brake hoses and sensor cables.
- Do not assume wheel alignment is unchanged after disturbing strut or arm joints.
Upgrades, maintenance and UK MOT
Lowering or uprating should preserve adequate bump and rebound travel, damper compatibility, tyre clearance and headlamp alignment. Adjustable platforms require matched springs and secure locking. Modifications can affect electronic driver aids and must be declared to the insurer. Cutting coils creates an uncontrolled rate, poor seating and serious safety risk.
Coil springs have no fixed universal replacement interval, but inspection during servicing, tyre work and annual testing can find corrosion early. UK MOT assessment considers fractured, insecure, significantly weakened or incorrectly located suspension springs. A pass does not guarantee remaining fatigue life, so newly developing knocks or height changes still require investigation.
Coil spring FAQs
Q: Should coil springs be replaced in pairs?
A: Normally yes on the same axle, so rate and ride height remain balanced.
Q: Does the shock absorber hold the car up?
A: Usually the coil spring carries static weight; the damper controls movement.
Q: Can I identify a spring only by its colour marks?
A: Use marks as supporting evidence, but confirm the full vehicle and part references.
Q: Why has the bottom coil broken?
A: Water, salt and grit collect near the seat, damaging coating and initiating fatigue corrosion.
Q: Can a broken spring damage a tyre?
A: Yes. A sharp end can contact the sidewall, brake hose or other nearby parts.
Q: Will new springs raise the vehicle?
A: They can restore designed height; the result depends on correct specification and the condition of seats and mounts.
Q: Are sport and standard springs interchangeable?
A: Not casually. Rate, free length, damper travel and geometry are calibrated together.
Q: Is surface rust acceptable?
A: Light staining differs from deep pitting or section loss; clean inspection is needed where corrosion is concentrated.
Q: Can I replace a spring without a compressor?
A: Only if the manufacturer procedure safely releases all spring load by another controlled method.
Q: What causes a spring to clunk while steering?
A: A binding top bearing, displaced end coil, damaged pad or fracture can wind and release the spring.
Q: Do heavy-duty springs increase legal payload?
A: No. Manufacturer axle, tyre and gross-weight limits remain controlling.
Q: Is alignment required after replacement?
A: Check the vehicle procedure; disturbing struts or arms often justifies measurement.
Q: Will a broken coil spring fail an MOT?
A: A fractured, insecure or seriously weakened spring can fail and may be dangerous.