1 Product
Your Current Vehicle
Or
Select Your Vehicle
Shop Transmission Filter by Brand
Only manufacturers with matching products in the current catalogue are shown.
Transmission Filter for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for Transmission Filter
Popular model families are ranked by the number of matching catalogue products.
Related Categories for Transmission Filter
Explore related part types from the same catalogue group.
Transmission filtration is matched to a specific lubrication circuit
Gearboxes circulate oil to carry heat, lubricate loaded contacts and, in hydraulic designs, apply clutches or move control valves. The filter must remove damaging particles without starving the pump at cold start or high demand.
There is no universal transmission filter. Its medium, flow area, bypass behaviour and physical pickup position are engineered around one transmission family and its approved lubricant.
Where filters are used
| Gearbox system | Possible filter arrangement | Service concern |
|---|---|---|
| Torque-converter automatic | Sump pickup or integrated filter pan. | Hydraulic pressure and clutch debris. |
| Continuously variable transmission | Internal strainer plus external cartridge on some designs. | Pulley control and specification-sensitive fluid. |
| Wet dual-clutch gearbox | Sump element, pressure filter or both. | Clutch material and mechatronic cleanliness. |
| Dry dual-clutch gearbox | Separate gear and actuator circuits may differ. | Do not assume the clutch type defines the oil system. |
| Automated manual | Gear oil may be unfiltered; hydraulic actuator may have its own circuit. | Identify which reservoir and component are being serviced. |
| Transfer or hybrid transaxle | Screen, magnet or no routine filter. | Architecture may not resemble a conventional automatic. |
Filter forms and construction
Suction filters
A broad, relatively open element sits between the sump and pump. Its inlet neck seals into a bore, and the body must sit at the designed height above the pan. A leaking neck seal allows air to enter; a wrongly shaped pickup can uncover during acceleration.
Pressure-side cartridges
Finer media can be used after the pump, but the housing and element must withstand system pressure. Cap O-rings, standpipes and bypass valves are part of the design, not interchangeable packaging details.
Integrated filter pans
Many moulded pans contain a permanent pickup and filter. Replacing only a separate gasket is not equivalent to renewing the filtration assembly. Plastic construction requires clean threads, correct fastener sequence and accurate low torque.
Spin-on units
Externally mounted filters resemble engine-oil filters but may have different threads, valves, pressure capability and media. Match the transmission reference exactly.
Identify the transmission before choosing parts
| Evidence | What it confirms | Why it is stronger than appearance |
|---|---|---|
| VIN build record | Factory transmission and equipment combination. | One body range can use several gearboxes. |
| Gearbox code or tag | Family, ratio set and design revision. | Engine size does not uniquely identify it. |
| Original part number | Existing filter or pan specification. | Revisions can change ports and pickup. |
| Production date | Applicable service information and hardware. | Changes often occur within a model year. |
| Pan and housing layout | Integrated or separately serviceable element. | Catalogue images may show several variants. |
| Fluid label or manual | Approval, capacity and level method. | Colour is not a technical specification. |
| Drive configuration | Case, sump and cooler routing. | All-wheel-drive packaging can alter parts. |
Filtration, magnets and normal wear
Friction linings shed fine non-ferrous material, while gears and bearings generate microscopic metal. A filter captures suspended debris above its effective pore size. Magnets in the sump collect ferrous material that would otherwise circulate.
A smooth grey paste on magnets can represent accumulated fine wear. Sharp flakes, chunks, rollers, bronze-coloured particles or thick fibrous deposits are evidence of an internal problem. Photograph and retain unusual material for diagnosis rather than washing it away immediately.
Why flow capacity matters
Cold transmission oil is more viscous and harder to draw through media. At high speed, the pump requires greater volume. A blocked, collapsed or overly restrictive element can create inlet vacuum, cavitation and aerated oil. Hydraulic pressure then becomes unstable even when the fluid level is nominally correct.
Some elements incorporate a bypass that opens at a designed pressure difference. Its purpose is to preserve flow, not to make incorrect filters acceptable. A substitute with the wrong calibration can pass contaminants or starve the circuit.
Fluid approvals and operating limits
Transmission oils are blended for specific friction materials, pump clearances, gear contacts and temperature ranges. Conventional ATF may need controlled clutch friction; CVT fluid must support belt or chain traction; dual-clutch fluid serves gears, bearings and wet clutches. Manual gear oil can contain a different additive balance for synchronisers.
Use the exact approval stated for the gearbox, including any supersession recognised by its manufacturer. Broad multi-vehicle claims should be checked against that approval. Mixing an unknown remainder with new oil creates an unverified blend.
Service intervals and demanding use
Follow the relevant schedule for the transmission rather than a universal mileage. Heat is a major ageing factor. Towing, repeated hill work, urban stop-start use, performance driving, high ambient temperature and restricted cooler airflow can accelerate oxidation.
A gearbox described as filled for life may still have inspection, leak repair or severe-use guidance. It does not mean the lubricant is chemically unchanged forever, nor that an internal filter is accessible as ordinary maintenance.
Service approaches
| Approach | Useful outcome | Important boundary |
|---|---|---|
| External cartridge change | Renews accessible fine filtration. | Does not inspect debris in the sump. |
| Pan removal and filter change | Allows magnet cleaning and internal inspection. | Only part of the total fluid drains. |
| Integrated-pan renewal | Replaces filter, pickup and sealing assembly. | Pan can be damaged by incorrect torque. |
| Drain and refill | Replaces the drainable oil volume. | Not equivalent to filter renewal. |
| Fluid exchange | Can renew a larger proportion of fluid. | Must be approved and is not a repair for wear. |
| Failure decontamination | Addresses debris in cooler and lines after damage. | Some components cannot be flushed effectively. |
Safe pan and filter service
- Retrieve the gearbox code, service method, fluid approval, level temperature and tightening data.
- Record existing faults and assess shift operation before service when the vehicle is safe to drive.
- Confirm the fill point is accessible, then raise the vehicle level on correctly rated supports.
- Clean the exterior and drain hot fluid carefully into a clean measured container.
- Lower the pan evenly, observing the position of magnets and deposits.
- Remove the filter without leaving its old neck seal in the housing or spilling dirt into exposed passages.
- Clean approved surfaces with lint-free materials; do not scratch aluminium or introduce excess sealant.
- Install the filter fully, fit specified new seals and start every fastener by hand.
- Tighten in sequence, refill initially and circulate oil through the commanded selections as instructed.
- Set the final level at the prescribed temperature and operating state, then road-test and inspect for leaks.
Level setting and thermal expansion
Many transmissions use a standpipe or level port instead of a dipstick. The result is valid only with the vehicle level, at a specified oil temperature and often with the engine running so the pump fills hydraulic circuits. Too little oil draws air; too much can foam or raise internal pressure.
Use the correct transmission-temperature data, not engine coolant temperature. If the allowed window is missed, let the unit cool and repeat the process. The quantity drained is useful evidence but not a substitute for the final method.
Symptoms requiring diagnosis
| Symptom | Possible filtration relationship | Other important causes |
|---|---|---|
| Pump whine | Restricted pickup or inlet air leak. | Low level, worn pump or bearing. |
| Delayed drive | Slow pressure build from restriction. | Seal leakage, clutch wear or drain-back. |
| Shift flare | Unstable apply pressure. | Solenoid, valve body or friction damage. |
| Ratio warning | Hydraulic supply may be inadequate. | Speed sensors, clutch slip or mechanical failure. |
| Shudder | Contaminated fluid can affect friction control. | Clutch, converter, engine or driveline fault. |
| Leak after service | Seal, pan or filter housing disturbed. | Incorrect level or damaged cooler line. |
| Burnt oil and debris | Filter may be loaded by internal failure. | Overheating and worn friction elements require repair. |
Adaptations and post-service work
Shift adaptations compensate for clutch and hydraulic behaviour. Do not reset them automatically after routine filtration service. Stored values can help diagnose wear, and a reset may demand a specific relearn drive that is inappropriate when a fault remains.
After servicing, confirm every selector position, engagement time, shifts, temperature and lock-up or CVT operation as applicable. Scan for new codes and inspect the pan, plugs, cooler connections and undertray after a heat cycle.
Common mistakes
- Choosing a filter by engine capacity rather than gearbox code.
- Using a fluid because its colour resembles the drained oil.
- Leaving the old pickup O-ring inside the pump bore.
- Adding gasket sealant where a moulded dry seal is specified.
- Over-tightening a plastic pan or low-torque cover.
- Discarding debris before its diagnostic significance is assessed.
- Setting fluid level with the vehicle tilted or outside its temperature window.
- Resetting adaptations to conceal an unresolved shift complaint.
Safety and environmental care
Transmission fluid can be hot enough to burn, and exhaust components remain hot nearby. Wear eye protection and gloves, use a broad drain container and support the vehicle independently of a jack. Keep hands away from rotating wheels and driveline parts during running checks.
Collect oil for responsible recycling and clean spills promptly. A transmission leak can reach the exhaust or tyres and can rapidly make the gearbox undriveable. Stop for severe slipping, loss of drive, a major leak, abnormal mechanical noise or an overtemperature warning.
Transmission filter FAQs
Q: Does every transmission have a replaceable filter?
A: No. Some have routine elements, some integrated parts and others no accessible service filter.
Q: Is a transmission filter only for automatics?
A: It is most common in hydraulic transmissions, but some CVT, dual-clutch and actuator systems have serviceable filtration.
Q: Can I select it using the engine code?
A: Not safely; confirm the exact gearbox code, VIN and production date.
Q: Is transmission fluid colour a specification?
A: No. Use the precise manufacturer approval stated for the gearbox.
Q: Can one filter kit fit an automatic and a CVT?
A: Only if explicitly catalogued for both exact units; their filtration and fluid needs commonly differ.
Q: Will a new filter stop clutch slip?
A: It cannot restore worn friction material or repair mechanical damage.
Q: Is fine grey material on a magnet normal?
A: A modest paste may be expected, but flakes, chunks or heavy debris need investigation.
Q: Must the pan be replaced?
A: Yes when the filter is integrated; otherwise inspect the separate pan against service limits.
Q: Why is oil temperature used during filling?
A: Thermal expansion changes level, so the specified range makes the check repeatable.
Q: Should I use extra sealant on the gasket?
A: Only where instructed; excess material can leak or obstruct internal passages.
Q: Should adaptations be reset?
A: Not for every filter change; follow the transmission-specific instruction.
Q: Can I flush a gearbox with an unknown history?
A: Assess its condition first and use only a method approved for that transmission.
Q: When should I stop driving?
A: Stop for rapid fluid loss, loss of drive, severe slip, overheating or harsh mechanical noise.