3 Products
Your Current Vehicle
Or
Select Your Vehicle
Why flexible brake hoses are essential
Rigid brake pipe efficiently carries pressure along the body, but cannot accommodate steering and suspension movement at each wheel. The flexible hose bridges that moving joint. It must change shape repeatedly without changing internal volume significantly, kinking or transmitting strain to the metal pipe and caliper.
Because braking pressure acts on every internal surface, construction and crimp quality are safety-critical. A small defect can progress from seepage to rupture, while an internally collapsed liner can behave like a one-way valve.
How hydraulic pressure travels through the hose
- Pedal force moves the master-cylinder piston and pressurises brake fluid.
- Pressure passes through ABS hydraulic valves and rigid pipes.
- The flexible hose carries it across the moving suspension joint.
- Fluid pressure acts on the caliper or wheel-cylinder piston area.
- Friction components apply to the disc or drum.
- When the pedal releases, pressure falls and fluid can return freely.
- The hose flexes with wheel travel while remaining clear of surrounding parts.
Hose designs and end connections
| Design | Typical features | Service focus |
|---|---|---|
| Rubber reinforced hose | Elastomer liner and cover with textile reinforcement. | Cracks, swelling, abrasion, age and correct routing. |
| Low-expansion braided hose | Inner liner surrounded by metal braid and protective coating. | Approval, end-fitting manufacture, kink radius and abrasion protection. |
| Banjo-ended hose | Ring fitting secured to caliper by hollow bolt. | Correct angle, new washers, bolt length and fluid passages. |
| Female swivel union | Connects to rigid pipe flare nut without rotating the hose. | Thread, seat form, bracket clip and corrosion. |
| Male threaded end | Screws into caliper, cylinder or junction block. | Seal type, insertion depth and avoiding hose twist. |
| Multi-section axle hose | Flexible links join body, axle and individual wheel pipes. | Axle articulation, T-piece security and total travel. |
Pressure, volume and pedal feel
Brake fluid is treated as nearly incompressible, so pedal displacement should move pistons rather than expand pipes. Reinforcement limits hose growth under pressure. Excessive expansion can make the pedal feel springy, although air, caliper flex, bearing clearance and master-cylinder faults can produce similar symptoms.
- Burst strength: must exceed maximum system pressure with an appropriate safety margin.
- Volumetric expansion: needs control to preserve pedal response.
- Impulse life: construction must withstand repeated pressure cycles.
- Flex endurance: hose and crimps must survive steering and suspension motion.
- Temperature resistance: protects the liner near brakes and exhaust parts.
- Fluid compatibility: prevents swelling, softening or cracking.
- Permeation resistance: limits moisture and vapour transfer through materials.
Hose construction
Inner liner
The bore carries fluid and must remain chemically stable and smooth. Internal delamination can form a flap that admits pressure during application but delays release. This may leave a wheel hot even though the hose looks normal.
Reinforcement
Braided textile or metal layers contain pressure and limit expansion. Exposed reinforcement indicates cover failure and cannot be safely patched. A tight kink permanently damages layer geometry.
Outer cover and sleeves
The cover resists weather, ozone and abrasion. Moulded buffers and sleeves are positioned where the hose passes brackets or nearby components; moving them can expose a vulnerable section.
Ferrules and fittings
Crimped ferrules join flexible construction to machined ends. Corrosion at the transition, loose fittings or seepage are replacement conditions. End orientation is fixed on many hoses and should not be corrected by twisting the flexible body.
Materials and deterioration
| Material/part | Purpose | Damage concern |
|---|---|---|
| EPDM inner/outer rubber | Compatible with specified glycol brake fluid and weather. | Petroleum contamination causes swelling and loss of strength. |
| Textile braid | Contains pressure with flexible construction. | Broken fibres after kink or abrasion reduce safety margin. |
| PTFE liner | Low expansion and chemical stability in approved assemblies. | Requires controlled bend radius and engineered end fittings. |
| Stainless braid | Restrains liner expansion and resists corrosion. | Uncovered braid can saw through adjacent materials. |
| Plated steel fitting | Provides strong threaded or banjo connection. | Salt corrosion attacks flats, seats and crimp area. |
| Protective polymer jacket | Prevents braid abrasion and dirt entry. | Cuts reveal braid and permit rubbing damage. |
Selecting the right hose
| Check | Why it matters | Evidence |
|---|---|---|
| Axle and side | Length, brackets and banjo angle may be handed. | Catalogue position and physical route. |
| End threads/seats | Same diameter can use different pitch or flare form. | OE reference and technical dimensions. |
| Overall/working length | Must accommodate lock and full suspension travel. | Specified length and installed articulation check. |
| Bracket location | Controls bend path and prevents chafing. | Compare grommets, flats and retaining clips. |
| Brake option | Larger calipers or different knuckles alter connections. | Disc/caliper specification and build codes. |
| Production date | Pipe union or suspension revision may change hose. | VIN and actual build date. |
Brake fluids and compatibility
Use the exact fluid specification stated by the vehicle manufacturer. DOT 3, DOT 4 and DOT 5.1 are glycol-based classifications with differing performance, while silicone DOT 5 is not interchangeable. Some hydraulic systems use mineral fluid and require materials designed for it. Mixing incompatible fluid can destroy seals and hoses throughout the system.
Glycol fluid absorbs moisture, lowering boiling resistance over time and promoting corrosion. Follow the specified change interval and use fresh fluid from a sealed container. Never lubricate hose fittings with engine oil or mineral grease.
Inspection through full movement
- Secure the vehicle on approved supports and remove the wheel where required.
- Clean enough dirt to inspect without damaging the cover.
- Look for cracks, bulges, wetness, flattened areas, exposed braid and corroded crimps.
- Turn steering from lock to lock while observing tension and contact.
- Move suspension through safe representative travel and check the hose does not become taut.
- Apply pedal pressure while watching for local ballooning.
- Inspect rigid pipe unions, bracket clips and caliper movement.
- Compare release at the bleed screw only using a controlled diagnostic procedure.
Symptoms and urgency
| Symptom | Possible hose cause | Response |
|---|---|---|
| Visible fluid leak | Crack, failed crimp or damaged fitting. | Do not drive; recover and repair the vehicle. |
| Bubble under pedal pressure | Reinforcement failure beneath the cover. | Replace immediately and inspect the opposite side. |
| Brake remains applied | Internally collapsed liner restricting return. | Diagnose hose, caliper and hydraulic source before further use. |
| Soft pedal | Hose expansion, though air or other faults may be responsible. | Pressure-test and bleed; do not accept uncertain pedal feel. |
| Hose rubbing tyre | Wrong routing, missing clip or incorrect length. | Stop before the cover is worn through. |
| Cracked outer surface | Age, ozone, heat or chemical exposure. | Assess promptly and replace when deterioration exceeds criteria. |
Removal and installation
Clean unions first and use a flare-nut spanner to reduce damage. Cap open pipes with clean compatible closures and prevent the reservoir draining unnecessarily. If a rigid pipe twists with its nut, stop before it fractures. Penetrating products must not enter the hydraulic system.
Install the hose without torsion, using flats on the fitting where provided. Fit new banjo washers, clips and locking hardware. Check that suspension movement does not pull the hose and that the wheel cannot rub it. Bleed in the specified order, including diagnostic ABS activation where required, and test every joint under firm pressure.
Common mistakes
- Clamping the hose shut with locking pliers.
- Letting a caliper hang from the flexible line.
- Twisting the hose to align a fixed banjo fitting.
- Reusing crushed sealing washers.
- Mixing metric and imperial or different flare threads.
- Allowing braid or rubber to rub a tyre or suspension arm.
- Using universal hose without verified pressure approval and end manufacture.
- Contaminating friction surfaces with brake fluid.
- Bleeding until the reservoir runs empty.
- Driving before pumping the pedal and checking for leaks.
Upgrades, maintenance and legal considerations
Approved low-expansion hoses can change pedal response, but must be designed for the exact vehicle, supported correctly and protected against abrasion. A firmer pedal does not increase tyre grip or correct worn calipers, contaminated fluid or unsuitable pads. Brake modifications should be declared to the insurer.
Hoses should be inspected during servicing and whenever brakes or suspension are disturbed. There is no safe repair for a cut, blistered or internally damaged flexible brake hose. The UK MOT considers leaks, bulges, damage, chafing, excessive deterioration and insecure routing. A seriously defective hose can be dangerous and should prevent road use.
Brake hose FAQs
Q: Can a brake hose fail internally?
A: Yes. A damaged liner can restrict fluid return and leave a brake applied.
Q: Should brake hoses be replaced in pairs?
A: Inspect both sides carefully; paired replacement may be sensible where age and exposure are equal.
Q: Can I clamp a hose during caliper work?
A: Do not use crushing tools; follow an approved fluid-control method.
Q: Why does one wheel remain hot?
A: A collapsed hose, seized caliper or hydraulic/parking mechanism fault may retain pressure.
Q: Is surface cracking dangerous?
A: Cracking indicates deterioration and requires assessment; deep cracks or exposed reinforcement demand replacement.
Q: Can a longer hose be fitted safely?
A: Only if it is the approved application and remains clear through all movement.
Q: Are braided hoses road legal?
A: Use properly approved, vehicle-specific assemblies with safe routing and documented manufacture.
Q: Can a hose cause a soft pedal?
A: Excess expansion can contribute, but air, fluid, calipers and other hydraulic faults also need checking.
Q: Must banjo washers be renewed?
A: Yes, use the specified new sealing washers and correct bolt.
Q: Which brake fluid should be used?
A: Only the vehicle manufacturer's exact specification; not all DOT or mineral fluids are compatible.
Q: Can a leaking hose be taped temporarily?
A: No. Hydraulic pressure makes external patching unsafe; recover the vehicle.
Q: Why must the hose not be twisted?
A: Torsion changes bend behaviour, stresses crimps and can kink the bore.
Q: Will a damaged brake hose fail an MOT?
A: Leakage, bulging, serious chafing or deterioration can fail and may be dangerous.