1 Product
Your Current Vehicle
Or
Select Your Vehicle
Shop MAP Sensor by Brand
Only manufacturers with matching products in the current catalogue are shown.
MAP Sensor for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for MAP Sensor
Popular model families are ranked by the number of matching catalogue products.
Related Categories for MAP Sensor
Explore related part types from the same catalogue group.
What absolute manifold pressure represents
Absolute pressure is measured from a theoretical perfect vacuum. Atmospheric pressure at sea level is roughly 100 kPa but changes with weather and altitude. A scan value of 30 kPa at petrol idle therefore represents substantial manifold vacuum, not 30 kPa of boost.
Gauge boost subtracts atmospheric pressure from manifold absolute pressure. Confusing these units can turn a normal reading into a false diagnosis.
MAP sensor technologies
| Design | Output | Diagnostic consideration |
|---|---|---|
| Analogue piezoresistive | Voltage changes with diaphragm strain. | Transfer curve and pressure range are application-specific. |
| Digital pressure sensor | Frequency, pulse width or serial data. | Requires suitable scope or scan data. |
| TMAP sensor | Pressure plus intake-air temperature. | Circuits can fail independently. |
| Remote hose sensor | Sensor connects to manifold by vacuum hose. | Hose blockage, leaks and fuel contamination matter. |
| Charge-pipe sensor | Measures boosted air before or after intercooler. | Location and range differ from manifold MAP. |
| Dual-range/barometric unit | Separate or combined ambient pressure channel. | Compare channels at key-on where appropriate. |
How pressure reaches the electronics
Diaphragm
A micromachined diaphragm deflects under pressure difference. Tiny resistive elements change value as it bends.
Signal conditioning
Internal electronics compensate temperature and convert the bridge output into voltage or digital data. Supply and ground quality directly affect the result.
Pressure port
The port exposes the diaphragm to manifold pressure while protecting it from flow. Carbon, oil or ice can delay response without an electrical fault.
How the ECU uses MAP
Speed-density petrol systems estimate incoming air mass from MAP, temperature, displacement, volumetric efficiency and engine speed. Systems with a MAF sensor use MAP as a plausibility check and transient-load input.
Diesel engines use pressure to control turbocharger vanes or wastegates, EGR flow and smoke limitation. At key-on, MAP may provide a barometric reference if no separate sensor exists.
Vacuum, atmospheric pressure and boost
| Condition | Expected trend | If implausible |
|---|---|---|
| Key on, engine off | MAP close to barometric pressure. | Check sensor bias, port and barometric reference. |
| Petrol warm idle | Pressure falls as manifold vacuum rises. | Check leaks, timing, compression and throttle. |
| Wide-open naturally aspirated load | MAP approaches atmospheric pressure. | Restriction or sensor range issue possible. |
| Turbocharged load | MAP rises above atmospheric within control target. | Boost leak, turbo, actuator or signal fault. |
| Engine shutdown | Pressure returns toward atmosphere. | Blocked port or slow sensor response. |
| Cranking | Regular pressure pulses/average drop. | Mechanical timing or compression evidence. |
Exact fitment evidence
| Check | Possible variation | Why it matters |
|---|---|---|
| Engine code/output | Naturally aspirated or different boost level. | Pressure range and calibration change. |
| Sensor location | Manifold, charge pipe or intercooler outlet. | Temperature and expected pressure differ. |
| Pressure range | One-, two-, three-bar or other scaling. | Wrong range biases or saturates signal. |
| Integrated temperature | MAP-only or TMAP. | Connector and ECU inputs differ. |
| Connector/pins | Supply, ground, signal and IAT assignment. | Plug shape alone is insufficient. |
| Port/flange | Depth, bolt position and O-ring. | Controls sealing and response. |
| Build date | Revised sensor or ECU calibration. | Follow production breaks. |
| Supersession | Updated seal, harness or software. | Fit approved package together. |
Key-on plausibility checks
Before starting, compare MAP with a trustworthy barometric value. They should be close when the manifold is at ambient pressure. Account for altitude and weather; a fixed universal sea-level number is not a valid limit.
If scan data offers both MAP and BARO, a large difference supports investigation. A shared biased five-volt supply can affect several sensors simultaneously.
Software plausibility models
The ECU predicts manifold pressure from throttle opening, engine speed, airflow, valve timing and turbo command. It may set a range fault when the MAP signal remains electrically valid but conflicts with that model. The conflicting input—not necessarily MAP—can be the failed one.
Compare throttle angle, MAF, cam position, EGR command and boost actuator data at the same timestamp. Freeze-frame evidence is especially useful because a substitute value used after the fault may look steadier than the original bad signal.
Live response and waveform testing
A rapid throttle opening on a petrol engine should drive MAP upward promptly; closing it should produce a strong drop. A slow trace can indicate a restricted port or excessive filtering. On boost, compare desired and actual pressure through a controlled load.
An oscilloscope can expose noise, dropouts and response delay. Keep test leads away from belts and turbo heat and use safe road or dynamometer procedures.
Fault patterns
| Symptom/code | Possible MAP issue | Other causes |
|---|---|---|
| Circuit high/low | Open, short, supply or sensor electronics. | Harness and shared reference faults. |
| Range/performance | Bias, blocked port or wrong sensor range. | Vacuum leak, timing and EGR. |
| Underboost | Sensor over-reads or responds slowly. | Charge leak, turbo, actuator and exhaust restriction. |
| Overboost | Sensor under-reads actual pressure. | Stuck vanes, wastegate or control hoses. |
| Black diesel smoke | Low pressure signal affects air calculation. | MAF, EGR, injectors and boost leak. |
| High petrol fuel trim | MAP bias alters calculated load. | Unmetered air, fuel pressure and oxygen sensor. |
| Intermittent limp mode | Heat/connector dropout. | Actual boost-control instability. |
Intake and boost leaks
A split hose downstream of a turbo can lose compressed air and make actual MAP fail to reach target. On petrol engines, manifold vacuum leaks raise idle MAP and alter fuel trims. Pressure or smoke testing must stay within system limits.
Inspect clamps, intercooler seams, brake-servo hose, crankcase ventilation and manifold gaskets. Do not replace a truthful sensor for pressure that is genuinely wrong.
Carbon, oil and moisture contamination
EGR soot mixed with oil mist can plug a manifold sensor port, especially on diesels. Oil from a failed turbo or excessive crankcase ventilation can cover the sensing cavity. Water in charge pipes may freeze in cold climates.
Clean only if the manufacturer permits it, using a sensor-safe product without tools touching the diaphragm. Correct the contamination source and replace a damaged or slow sensor.
Electrical testing
Use the wiring diagram. Many analogue sensors use a five-volt reference, sensor ground and output, with an extra temperature signal on a TMAP. Verify reference under load and ground voltage drop.
Back-probe with fine approved terminals; do not spread connector contacts. A signal voltage inside the nominal range can still be biased, so compare it with known applied pressure only using suitable calibrated equipment.
Removal and installation
- Record codes, freeze-frame and key-on/barometric comparison.
- Identify exact sensor location and whether it includes temperature.
- Switch ignition off and follow battery or high-voltage isolation instructions.
- Clean around the sensor so debris cannot enter the intake.
- Release the connector lock without pulling wires.
- Remove small fasteners with the correct tool and withdraw squarely.
- Inspect port, seal, manifold and connector for contamination or damage.
- Compare pressure range, tip, flange, pins and part reference.
- Fit the specified new O-ring with approved light lubrication if required.
- Seat fully and tighten the plastic flange to its low stated torque.
- Reconnect and clear only resolved codes.
- Confirm key-on plausibility and loaded boost response.
Common mistakes
- Confusing absolute pressure with gauge boost.
- Replacing the sensor from an underboost code without testing leaks.
- Choosing a lookalike with the wrong pressure range.
- Cleaning the diaphragm with a brush or compressed air.
- Ignoring a plugged manifold port.
- Testing continuity while missing a shared five-volt supply fault.
- Overtightening the small plastic mounting flange.
- Confirming idle only and skipping loaded control checks.
UK MOT and emissions relevance
A MAP fault can increase emissions, cause smoke and illuminate the emissions malfunction indicator lamp. An applicable warning or emissions result outside limits can lead to MOT failure.
Boost-control faults can produce unsafe power loss or damaging overpressure. An MOT pass does not validate the sensor across the engine's pressure range.
Practical MAP-sensor FAQs
Q: What does a MAP sensor measure?
A: It measures absolute pressure in the intake manifold or charge-air path.
Q: Is MAP the same as boost pressure?
A: MAP includes atmospheric pressure; gauge boost subtracts it.
Q: What should MAP read with the engine off?
A: It should be close to local barometric pressure when the intake is open to atmosphere.
Q: Are MAP and MAF sensors the same?
A: No. MAP measures pressure; MAF measures entering air mass.
Q: Can a blocked sensor port cause a code?
A: Yes, it can delay or freeze pressure response.
Q: Can I clean a MAP sensor?
A: Only if approved, using sensor-safe product without touching the diaphragm.
Q: Can a boost leak mimic sensor failure?
A: Yes, because the sensor may accurately report pressure below target.
Q: Why does altitude affect MAP?
A: Atmospheric pressure falls with altitude, changing the absolute baseline.
Q: What is a TMAP sensor?
A: It combines manifold/charge pressure and intake-air temperature sensing.
Q: Does a new sensor need coding?
A: Usually not, though adaptations or fault clearing may be specified.
Q: Can a bad MAP sensor cause smoke?
A: Yes, through incorrect load or boost control, especially on diesels.
Q: Can I test it with compressed air?
A: Only with regulated calibrated equipment and the approved off-vehicle procedure.
Q: Can a MAP fault fail the MOT?
A: It can through the warning lamp, smoke or excessive emissions.