1 Product
Your Current Vehicle
Or
Select Your Vehicle
Shop Parking Sensors by Brand
Only manufacturers with matching products in the current catalogue are shown.
Parking Sensors for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for Parking Sensors
Popular model families are ranked by the number of matching catalogue products.
Ultrasonic sensors calculate distance from echo time
A piezoelectric element emits a short sound burst above human hearing, then listens for reflections. The controller converts travel time into distance while accounting for temperature, sensor position and cross-talk from neighbouring channels.
Soft surfaces can absorb sound, narrow poles can reflect it away and very low objects can sit below the beam. Sensor coverage supplements mirrors, cameras and direct checks.
System layouts
| Layout | Coverage | Integration | Service focus |
|---|---|---|---|
| Four rear ultrasonic sensors | Rear bumper during reverse. | Buzzer or display. | Reverse activation and sensor positions. |
| Front and rear system | Both bumpers at low speed. | Manual switch and vehicle network. | Speed gating and front/rear loom. |
| Park-assist side sensors | Space measurement along body sides. | Steering-assist controller. | Exact outer positions and calibration. |
| Camera fusion | Distance zones over image. | Infotainment/display module. | Overlay, camera and sensor agreement. |
| Trailer-aware system | Rear coverage altered when towing. | Towing module detects connection. | Trailer coding and socket signals. |
Sensor position and acoustic angle
Each holder points the transducer across a defined part of the field. Inner and outer holders can have different wedges even when sensors share a number. Rotating an angled unit can make it detect the road or miss a corner.
Observe arrows, “up” marks and holder keying. A repaired bumper must maintain the original height, spacing and face angle.
Electrical arrangements
A three-wire sensor can contain power, earth and digital communication
Some sensors return an analogue or pulsed signal; others share a data bus along the bumper. A shorted sensor can pull down the line and make several channels appear absent.
Use the wiring diagram and suitable oscilloscope or diagnostic data. Do not expect a generic resistance value across an electronic transducer.
Activation logic
Rear sensing may require a valid reverse signal, while front sensing activates through a switch, previous reverse selection or low-speed condition. Door, tailgate, trailer and fault states can inhibit warnings.
Establish the intended logic before replacing components. A towing module can deliberately suppress rear sensors when a trailer is recognised.
Warnings and distance zones
Tone intervals generally shorten as distance reduces, becoming continuous near the calibrated limit. Displays can indicate a zone rather than centimetre accuracy. Different objects and approach angles change first detection.
Never use the continuous tone as permission to keep moving. Stop and inspect the actual clearance.
Environmental effects
Mud, ice, snow, thick wax and water films can damp or reflect the acoustic pulse. Heavy rain, nearby pneumatic tools or another ultrasonic system may produce temporary interference.
Clean with a soft compatible method. Do not scrape a painted membrane or direct a pressure washer closely at its edge.
Identify the exact sensor
Use VIN, build date, bumper, location and original number. Confirm connector orientation, body length, acoustic frequency, paint status and software supersession. Map each bumper position before removing several units.
Check holder and seal separately. A sensor loosely glued into a broken bracket will not maintain its intended acoustic plane.
Symptoms and diagnostic clues
| Symptom | Sensor possibility | Alternative source | Useful check |
|---|---|---|---|
| Long fault tone on activation | One channel missing/implausible. | Module, loom, coding or supply fault. | Scan codes and live distance by position. |
| False warning on clear ground | Misaligned, dirty or internally damp sensor. | Bumper deformation or attached accessory. | Clean, inspect angle and graph reading. |
| One obstacle zone absent | Specific transducer not transmitting. | Holder angle or local harness break. | Position test with controlled target. |
| Entire rear system dead | Shorted bus sensor possible. | Reverse input, common feed, module or trailer logic. | Activation data and bus isolation procedure. |
| Intermittent after rain | Water through sensor seal. | Connector or loom splice water ingress. | Inspect first wet point and terminal condition. |
| Wrong display side | Positions swapped during repair. | Configuration or display mapping. | Activate one known physical channel. |
Begin with cleaning and visual inspection
Clean every face, then inspect cracks, chips, pushed-in units and bumper paint build-up. Check that each sensor is flush, equally oriented and secure. Look behind for collision damage and stretched looms.
Record accessories such as tow bars, spare-wheel carriers or number-plate mounts that enter the sensing field.
Scan-tool diagnosis
Read the dedicated parking module and related body, gateway and towing modules. Record fault status and live distance/quality for every channel before clearing. A fixed minimum or maximum value can identify a failed or blocked channel.
Run supported actuator or sensor tests under controlled conditions with the vehicle immobilised.
Listening and touch tests
A functioning ultrasonic transducer may produce a faint tick felt through a fingertip or heard with suitable equipment. This proves some activity, not correct distance measurement or acoustic output strength.
Keep clear of a vehicle that could move and do not place the body between it and an obstacle while reverse is selected.
Power, earth and data checks
Back-probe through approved breakout leads without spreading waterproof terminals. Measure supply and ground under operating load. For shared communication, compare waveform at the module and bumper branch.
Disconnect channels only in the diagnostic order because a module may log additional faults. Never short a line to test whether the buzzer reacts.
Water ingress
Inspect seal lips, connector backs, bumper-loom splices and low points where water collects. Capillary travel can carry water away from the original entry point. Green copper beneath insulation needs an approved extended repair.
Do not fill a connector with arbitrary sealant; it can prevent terminal contact and trap moisture.
Painting sensors
Some sensors are supplied primed and may be painted within a defined process. Excess basecoat, metallic pigment or clearcoat mass changes membrane vibration. Others must remain unpainted.
Mask the connector and non-paint areas, follow film-thickness limits and never repaint repeatedly to cover damage.
Removal and bumper work
Release holders from behind rather than pressing the acoustic face. If bumper removal is required, disconnect nearby lighting, radar and camera equipment safely and support the cover to avoid creasing paint.
Check for high-voltage cables or impact sensors before drilling or heating. Factory retrofit templates define hole diameter and angle.
Installation controls
| Stage | Required control | Failure prevented |
|---|---|---|
| Identification | Part number, frequency and exact position match. | Incompatible signal and wrong coverage. |
| Holder | Correct angle, up mark and secure retention. | Road echoes and blind zones. |
| Surface | Approved paint thickness; face clean and flush. | Damped acoustic response. |
| Connector | Dry sound terminals and full lock engagement. | Intermittent bus failure. |
| Harness | Original clips, drip paths and abrasion clearance. | Water travel and chafing. |
| Configuration | Correct positions coded/learned as required. | Wrong display and unavailable features. |
| Field test | Known targets approach every sensing zone. | Undetected blind channel. |
Coding and calibration
Replacement modules and some sensor generations need variant coding. Automated-parking systems can require steering, camera or bumper calibration after repairs. Maintain stable battery voltage and record original configuration.
Do not select a different bumper or tow-bar setting simply to suppress warnings; configuration must describe the vehicle.
Controlled target testing
Use suitable broad and narrow targets at measured positions, moving them slowly while the vehicle remains secured. Test centre, corners and transitions between sensors. Compare display side and tone progression.
Do not use a person, child or animal as a test obstacle. Remember that a system can miss objects below or between its beams.
After collision or tow-bar work
A bumper can look restored while holders remain tilted. Check reinforcement, absorbers and loom clips. Tow equipment needs correct coding and physical clearance from sensor fields.
Systems sharing the bumper with radar may need separate calibration and safety checks; parking-sensor success does not verify radar alignment.
Safety and operating limits
Parking aids never transfer responsibility from the driver. Cameras have lens contamination and perspective limits; ultrasonic sensors have object and angle limits. Use direct observation and assistance where visibility is restricted.
Stop using automated parking if warnings are unavailable, displayed on the wrong side or contradict visible clearance. Diagnose before relying on it.
Common mistakes
- Buying by sensor diameter while ignoring frequency and software identity.
- Rotating an angled holder so the sensor reads the road.
- Applying excessive paint to the acoustic membrane.
- Replacing a ticking sensor without checking its live distance.
- Ignoring a shared bus short that disables several sensors.
- Gluing a sensor into a damaged bracket.
- Drilling a bumper without a template or hidden-component check.
- Using a person as a parking-system test target.
Practical parking-sensor FAQs
Q: Does a ticking sensor prove it works?
A: No; it may still report the wrong distance or weak echo.
Q: Can any same-size sensor be fitted?
A: No; match number, frequency, connector, software and position.
Q: Why does the system false-alarm in rain?
A: Check water films, ingress, contamination and bumper alignment.
Q: Can parking sensors be painted?
A: Only when permitted and within the specified coating thickness.
Q: Why are rear sensors disabled with a trailer?
A: Correct towing logic prevents warnings from the connected trailer.
Q: Can one failed sensor disable all of them?
A: Yes, especially if it shorts a shared supply or data line.
Q: Do new sensors require coding?
A: Some systems need configuration, position learning or calibration.
Q: Why is the warning shown on the wrong side?
A: Check swapped positions, holder mapping and configuration.
Q: Can sensors detect every obstacle?
A: No; low, narrow, soft and angled objects may be missed.
Q: Should adhesive touch the sensor face?
A: No; it changes vibration and acoustic performance.
Q: How is each zone verified safely?
A: Move a suitable inanimate target while the vehicle is secured.
Q: Does sensor testing verify bumper radar?
A: No; radar has separate alignment and calibration requirements.
Q: What confirms a complete repair?
A: Correct live distances, field coverage, display mapping and no faults.