73 Products
KYMCO
Finding the correct Kymco parts starts with identifying the exact motorcycle, not simply matching a familiar-looking component. The vehicle selector recognises applications including FILLY, DINK, AGILITY, CK, COBRA, DJ and DOWNTOWN. Those names can cover different generations, engines, body styles, braking packages and electrical systems, so registration, VIN, production date and technical dimensions all matter when narrowing a result.
Powered two-wheelers demand particular attention to engine capacity, model code, wheel and brake specification. Service items, lighting, ignition parts and filters may change between a scooter, commuter, touring or performance derivative. Inspect both sides of the machine where components work as a pair, and never substitute a part with a different load, speed, electrical or friction rating.
The current range is strongest in areas such as lighting and visibility. Diagnose the system before ordering: a warning light, leak, noise or uneven wear may be caused by wiring, mountings, contamination or another component rather than the obvious part. Check related seals, fixings, hoses and connectors, and follow the manufacturer’s repair sequence and tightening data.
Before beginning the job, read the full fitting notes and establish whether the component is supplied individually, as an axle pair or as part of a kit. Check which clips, gaskets, bolts and fluids are included, then obtain any additional single-use hardware. This prevents a safe, clean repair from being interrupted after dismantling and helps ensure the surrounding system is returned to the intended specification.
Safety-critical work needs suitable tools and competence. Brakes, steering, wheels, fuel systems and high-voltage equipment should not be disturbed without the correct procedure. After fitting, complete any bleeding, priming, bedding, coding or calibration required, then carry out static and controlled functional checks before normal road use.
Use the model and product information below as a practical starting point, then verify every application-specific detail on the product page. Keep the vehicle details beside you while comparing alternatives, particularly where several dimensions or production notes are shown. Compatible Kymco parts are listed in this collection.
Your Current Vehicle
Or
Select Your Vehicle
Choosing the right Kymco parts
A search for Kymco parts is most reliable when treated as an identification exercise. Model name, generation and engine are the starting points, but the final choice may depend on the production month, body, gearbox, axle, steering side and factory option codes. The aim is to select a part that fits, connects and performs exactly as the vehicle specification requires.
Applications represented in the selector include FILLY, DINK, AGILITY, CK, COBRA, DJ, DOWNTOWN and FEVER. This is useful orientation, not a substitute for the final application checks. Where a model appears more than once, the body designation or code may identify a separate generation or derivative.
How to identify the exact application
- Record the registration, VIN, model series and build date.
- Confirm the engine or motor, fuel type, gearbox and driven axle.
- Note the body style, wheelbase, trim and any sports, towing or heavy-duty package.
- Diagnose the failed setup and record fault codes or measurements ahead of clearing them.
- Compare OE or cross-reference numbers, dimensions, connections, fitting position and included hardware.
- Read the installation notes for production splits, paired replacement, calibration and single-use fasteners.
For motorcycles and scooters, add engine capacity, exact model code, wheel size, brake arrangement and chain or belt specification. If the removed part is available, compare it before dismantling the vehicle further, while remembering that an approved supersession can have a revised appearance.
Kymco model and body references
| Selector model | Application context | Details still needed |
|---|---|---|
| FILLY | motorcycle or scooter model series | Confirm generation, build date, powertrain and fitted equipment. |
| DINK | motorcycle or scooter model series | Verify generation, build date, powertrain and fitted equipment. |
| AGILITY | motorcycle or scooter model series | Establish generation, build date, powertrain and fitted equipment. |
| CK | motorcycle or scooter model series | Confirm generation, build date, powertrain and fitted equipment. |
| COBRA | motorcycle or scooter model series | Establish generation, build date, powertrain and fitted equipment. |
| DJ | motorcycle or scooter model series | Confirm generation, build date, powertrain and fitted equipment. |
| DOWNTOWN | motorcycle or scooter model series | Establish generation, build date, powertrain and fitted equipment. |
| FEVER | motorcycle or scooter model series | Confirm generation, build date, powertrain and fitted equipment. |
Model tables help organise a search, but they cannot show every engine, market or running change. A model sold over several years can use differing filters, sensors, brakes or belts. Where the listing specifies a chassis range, engine code or “from/to” date, treat that note as component of the fitment requirement.
Model-specific service focus
FILLY
When working on a FILLY, begin with lighting and visibility: establish the lamp function, cap, voltage, optical approval and exact front, rear, left or right position. Continue by checking the powertrain, production split and fitting position. If database and physical evidence disagree, investigate the vehicle history or superseded reference instead of choosing the closest-looking alternative.
DINK
For this motorcycle or scooter model series, verify the lamp function, cap, voltage, optical approval and exact front, rear, left or right position. The DINK name might span more than one derivative, so retain the selector's body or series code and reconcile it with the VIN, build date and removed part before ordering.
AGILITY
For this motorcycle or scooter model series, verify the lamp function, cap, voltage, optical approval and exact front, rear, left or right position. The AGILITY name might span more than one derivative, so retain the selector's body or series code and reconcile it with the VIN, build date and removed part before ordering.
CK
When working on a CK, begin with lighting and visibility: confirm the lamp function, cap, voltage, optical approval and exact front, rear, left or right position. Continue by reviewing the powertrain, production split and fitting position. If database and physical evidence disagree, investigate the vehicle history or superseded reference instead of choosing the closest-looking alternative.
COBRA
When working on a COBRA, begin with lighting and visibility: confirm the lamp function, cap, voltage, optical approval and exact front, rear, left or right position. Continue by reviewing the powertrain, production split and fitting position. If database and physical evidence disagree, investigate the vehicle history or superseded reference instead of choosing the closest-looking alternative.
Parts represented in this collection
Current product evidence for Kymco is concentrated around lighting and visibility. Availability may change, and one category label may contain several designs. Use the table as an inspection guide, then rely on the individual product record for the final specification.
| Arrangement area | Important matching points | Related inspection |
|---|---|---|
| Lighting and visibility | Review lamp function, voltage, cap, homologation and left/right position. | Inspect neighbouring components ahead of ordering. |
What reliable performance depends on
| Factor | Effect on the repair | Practical control |
|---|---|---|
| Exact fitment | A near match can bolt on yet have the wrong travel, output, pressure, friction area or calibration. | Review every listed dimension, code and fitting note. |
| Arrangement condition | Wear, blockage, poor alignment or electrical faults elsewhere may damage a replacement. | Inspect the complete assembly and specified the root cause. |
| Materials and fluids | Seals, friction materials and lubricants must tolerate the intended temperature and chemistry. | Use the specified grade, approval and cleaning method. |
| Installation | Contamination, incorrect torque or poor routing causes leaks, noise and early failure. | Follow model-specific service specification with suitable tools. |
| Commissioning | Some arrangements need bleeding, priming, bedding, coding or calibration. | Complete the prescribed procedure before road use. |
Diagnosis before replacement
Good diagnosis separates the symptom from its cause. A noisy bearing can reflect misalignment, a new sensor code can originate in damaged wiring, and uneven brake wear may point to a seized slider or hose restriction. Preserve fault codes and measurements, inspect the surrounding assembly and test supplies, grounds or pressures prior to committing to a replacement.
Compare symptoms across operating states: cold and hot, stationary and moving, lightly and heavily loaded. For this motorcycle, relevant stresses may include lean angle, vibration, weather exposure, engine heat and repeated acceleration or braking. A fault that appears only under one condition often provides a better clue than the loudest symptom.
Construction, materials and specification
Automotive parts combine metals, elastomers, engineering plastics, friction compounds and electronic materials. Their grade and treatment matter. Heat-resistant rubber used in a coolant circuit is not automatically safe for fuel; a high-strength bolt is not interchangeable with one of the equivalent diameter but a varied pitch or tightening method; and a lamp with the equivalent cap might have a varied wattage or optical purpose.
| Specification | Typical variation | Why to verify it |
|---|---|---|
| Dimensions | Diameter, thickness, length, pitch, mounting centres and connector geometry. | Small differences may prevent fitment or change operating clearance. |
| Position | Front/rear, left/right, inner/outer, upper/lower or cylinder-specific. | Opposite-side parts might look alike but have mirrored fittings. |
| Rating | Load, pressure, voltage, current, temperature, speed or friction class. | A lower or unsuitable rating may create a safety or durability problem. |
| Material | Steel, alloy, rubber compound, polymer, ceramic or composite. | Material controls corrosion, flexibility, heat tolerance and chemical compatibility. |
| Approval | Vehicle-maker specification, E-marking or category-specific standard. | Road-use and assembly requirements can depend on the appropriate approval. |
Technology and application changes
Vehicle arrangements have evolved through better corrosion protection, tighter emissions control, networked electronics and more integrated assemblies. A superseded replacement can not look identical to the removed part, yet it might still be correct when the manufacturer cross-reference and technical data agree. Conversely, visual similarity alone never confirms interchangeability.
Networked control modules could require service mode, basic settings or calibration after mechanical work. Steering-angle, tyre-pressure, braking, lighting and emissions setups may all retain fault guidance. Use a diagnostic process suited to the vehicle; do not disconnect the battery as a universal reset, because doing so may lose learned values without curing the cause.
Wear, inspection and repair urgency
| Finding | Possible meaning | Recommended response |
|---|---|---|
| Fluid leak or fuel smell | Failed seal, hose, housing or joint. | Stop and investigate immediately if fuel or brake fluid is involved. |
| Grinding, knocking or increasing vibration | Excessive wear, looseness, contact or imbalance. | Avoid further use when steering, braking, wheels or drivetrain security might be affected. |
| Warning lamp or message | A monitored value or circuit is outside its expected range. | Read codes and test the arrangement; do not erase evidence first. |
| Uneven wear or pulling | Misalignment, restricted movement, pressure imbalance or tyre issue. | Examine both sides and measure the related geometry. |
| Overheating or burning odour | Drag, overload, poor cooling, short circuit or slipping drive. | Stop safely and allow diagnosis before further damage occurs. |
| Intermittent operation | Loose connection, moisture, heat-sensitive electronics or internal wear. | Test under the conditions that reproduce the fault. |
Maintenance and installation guidance
Plan the job ahead of lifting or isolating the vehicle. Obtain the repair procedure, tightening values, fluid specification and any special tools. Support the vehicle on rated stands at approved points; a jack is a lifting device, not safe working support. Protect painted surfaces from aggressive fluids and use eye, hand and respiratory protection appropriate to the task.
Keep open hydraulic, fuel, intake and cooling arrangements clean. Start threads by hand, replace disturbed seals and single-use fixings where instructed, and route cables or hoses through their original clips. On paired safety parts, follow the service guidance for axle or side-to-side replacement. Mixing incompatible friction materials, fluids or part ratings might create imbalance.
Following assembly, turn or move the mechanism by hand where appropriate, restore fluids, prime or bleed the circuit and reconnect arrangements in the specified sequence. Complete coding or calibration, then carry out a static check before a controlled low-speed test. Reinspect for leaks, heat, warning lamps, abnormal noise and loose fixings.
Common ordering and fitting mistakes
- Choosing by model name or image while ignoring build date and technical notes.
- Confusing a body designation with a distinct generation carrying the corresponding badge.
- Failing to review front/rear, left/right, axle or engine position.
- Assuming registration lookup removes the need to compare dimensions and references.
- Replacing a sensor without testing wiring, power, ground and the mechanical assembly it monitors.
- Reusing locking hardware, seals or torque-to-yield bolts against the repair instruction.
- Applying general grease or sealant to a setup that requires a compatible specialist product.
- Skipping bleeding, bedding, priming, coding, service mode or calibration.
Upgrades, modifications and UK road use
An upgrade must answer a defined require such as heat capacity, load, corrosion resistance or repeated heavy use. A component described as performance-oriented is not automatically better for a road vehicle: cold response, noise, comfort, emissions compatibility and service life may be worse outside its intended operating window. Review how the change affects connected setups and declare relevant modifications to the insurer.
Tyres, wheels, brakes, steering, suspension, drive chain or belt, lights and controls directly affect stability and the motorcycle MOT. An MOT is a minimum-condition check on the test date, not a maintenance schedule or proof that every part is suitable. The vehicle must remain safe and roadworthy between tests, and lighting, emissions or safety parts needs to retain the approvals needed for their application.
Kymco components FAQs
Q: How do I verify a part fits my Kymco?
A: Start with registration or VIN data, then match model series, build date, engine or motor, gearbox, position, dimensions, connector and reference numbers.
Q: Why does the equivalent model show more than one part?
A: Production changes, engine choices, body styles and optional equipment may create several valid specifications within one model name.
Q: Is a registration lookup conclusive?
A: It is a strong starting point, but imported vehicles, running changes and factory options mean the listing details and removed component needs to still be reviewed.
Q: May I order from the product photograph?
A: No. Images help recognition but might not show dimension, internal rating, pin function, side or production split.
Q: Needs to I use the VIN or engine code?
A: Use both when available. The VIN identifies the vehicle build, while the engine code may resolve powertrain-specific service components.
Q: Do related parts need replacement at the matching time?
A: Replace pairs, kits, seals and single-use hardware where the manufacturer instructs, and always assess the complete surrounding assembly.
Q: What causes a new part to fail early?
A: Common causes include incorrect vehicle match, contamination, unresolved arrangement faults, wrong fluids, poor alignment and omitted commissioning steps.
Q: Does a fault code prove a sensor is faulty?
A: No. It records a detected condition. Wiring, supply, ground, leaks or mechanical faults may produce the identical code.
Q: Might I fit Kymco parts myself?
A: Only where you have the correct data, tools and competence. Safety-critical and high-voltage work ought to be handled by an appropriately trained person.
Q: What must be reviewed after fitting?
A: Recheck torque, routing, fluid level, leaks, warning lamps and normal operation, then complete any bedding, calibration or controlled road test required.
Q: Could the fault affect the MOT?
A: Yes, if it affects braking, steering, tyres, suspension, visibility, lighting, emissions, structure or a monitored safety setup.
Q: When ought to the vehicle not be driven?
A: Stop when there is impaired braking or steering, an insecure wheel, fuel or brake-fluid leakage, severe overheating, restricted visibility or another immediate safety risk.