BMW X5 (E70) M 4.4L 555 hp Parts
Your Current Vehicle
Or
BMW Parts by Category
Catalogue-Matched Parts for This Vehicle
Compare up to ten catalogue-backed products. Confirm the exact vehicle and complete technical specification before ordering.
BMW Exact Vehicle Parts Guide
Compatibility, maintenance and safety guidance for the selected vehicle.
What to check for this exact BMW X5 (E70) M 4.4L 555 hp
This page is for the BMW X5 (E70) M 4.4L 555 hp, manufactured 07/2009–07/2013. The engine description is M, the recorded output is 555 hp and the recorded capacity is 4,395 cc. These details separate this vehicle from other engines, power outputs, production splits and body styles that can share a BMW model and engine description.
An exact vehicle selection removes much of the uncertainty found on a broad model page, but it is not a substitute for the complete product application. Confirm the VIN or registration result, production month, gearbox, driven wheels, steering position and factory equipment whenever the product notes require them. Brake packages, suspension options, electrical connectors, emissions equipment and component position can still divide parts within one exact vehicle.
How to use this exact vehicle page
- Confirm that BMW X5 (E70) M 4.4L 555 hp matches the vehicle being repaired.
- Choose a compatible category shown on this page.
- The next page keeps this exact vehicle selected.
- Compare any remaining axle, side, dimension, production or equipment choices.
- Read the complete manufacturer application and fitting notes before ordering.
The categories shown for this vehicle retain the selected application, but individual choices can still vary by component, production split and specification.
Compatible categories recorded for this vehicle
- Suspension Arms
- Anti-roll bar links
- Brake Pad Wear Sensor
- Cabin Filter
- Brake Hose
- Brake Discs
- Brake Pads
- ABS Sensor
- Suspension Bushes
- Air Suspension Compressor
- Handbrake Cable
- Ignition coil
Main systems and compatibility checks
| System | Typical components | Checks before ordering |
|---|---|---|
| Brakes | Discs, pads, sensors, hoses, calipers and fitting hardware | Axle, disc dimensions, caliper design, wear-sensor arrangement and paired replacement requirements. |
| Suspension and steering | Arms, bushes, dampers, springs, joints, mounts and bearings | Axle load, standard or sport setup, driven wheels, side, mounting design and alignment procedure. |
| Filters and service parts | Air, oil, fuel and cabin filters, plugs, belts and service seals | Housing, dimensions, complete reference, approval, production split and supplied seal arrangement. |
| Cooling and heating | Radiator, water pump, thermostat, tank, flanges, hoses and heater parts | Engine, gearbox cooling, air conditioning, connection layout, coolant specification and bleeding method. |
| Engine management | Air-mass, crankshaft, lambda, pressure and temperature sensors | Connector, position, engine-management revision, wiring condition and diagnosis of related mechanical faults. |
| Electrical and lighting | Starter, alternator, ignition, lamps, switches, regulators and motors | Electrical rating, connector, market, steering side, body location, control system and coding needs. |
| Transmission and driveline | Clutch, hydraulics, shafts, mounts, seals and transmission service parts | Exact gearbox, drive layout, dimensions, bolt pattern, fluid approval and filling procedure. |
Confirm compatibility from evidence, not appearance
Use the vehicle lookup as the starting point, then compare the complete replacement reference, dimensions, material, connector, mounting points and any supplied hardware. Product photographs can help identify a general design but are not final compatibility proof. A component that looks similar can differ in pressure rating, calibration, axle position, electrical pinout or installation depth.
Production dates should be read together with the VIN and product notes. A part listed “from” or “to” a month may sit close to a factory change, so compare the installed reference when more than one option is listed. Superseded references can be valid, but the replacement chain and technical notes must agree with the exact application.
Brakes, steering and suspension
For brake parts, confirm the axle, disc diameter, thickness, height, hub dimensions, caliper and wear-sensor arrangement. Inspect hub faces, sliders, hoses, bearings and tyres when diagnosing vibration or pulling. Friction and paired axle components are normally serviced as balanced sets where the repair information requires it. A red brake warning, fluid loss, grinding or materially reduced braking performance needs immediate assessment.
Suspension and steering noises can travel through the body and may involve more than the most visible joint. Check arms, bushes, links, springs, dampers, mounts, bearings, steering joints, wheels and tyres under the correct loading conditions. Alignment is normally completed after work that changes geometry, but alignment cannot compensate for worn joints, damaged wheels or an incorrect ride height.
Filters, ignition and engine service
Filter choice depends on the exact housing, dimensions, seal design and complete application. Keep contamination away from clean intake, oil and fuel circuits, renew specified seals and check for leaks after service. Engine oil needs the required approval as well as a suitable viscosity; a headline grade alone does not define additive performance or compatibility.
Spark plugs, glow plugs and ignition parts must match the required specification, reach, seat, heat range, electrical design and tightening procedure. Misfire, poor starting or an engine warning can also involve wiring, coils, fuelling, compression, air leaks or sensors. Save diagnostic evidence before clearing it and test the affected circuit rather than replacing parts from code wording alone.
Cooling, heating and fluid safety
Inspect the cooling circuit as a connected system. The radiator, expansion tank, cap, thermostat, water pump, hoses, flanges, fan and heater circuit can influence the same symptom. Never open a hot pressurised system. Use the specified coolant chemistry and mixture and follow the prescribed filling and bleeding procedure; trapped air or an unresolved leak can cause unstable temperature or repeat overheating.
| Item | Confirm before use | Why it matters |
|---|---|---|
| Engine oil | Required BMW approval, viscosity and service requirement | Viscosity alone does not establish the required performance specification. |
| Coolant | Approved chemistry, mixture, cleanliness and bleed procedure | Incorrect mixing or trapped air can reduce protection and cooling reliability. |
| Brake fluid | Specified grade, condition and safe bleeding method | Moisture lowers boiling performance and any fluid loss is safety-critical. |
| Gearbox and final-drive fluids | Exact unit identification, approval, temperature and level procedure | Different transmissions and final drives can use different lubricants and methods. |
| Fasteners and seals | Correct part, single-use status, torque and angle sequence | Incorrect reuse or tightening can damage threads, joints and sealing faces. |
Materials, construction and installed specification
| Part area | Construction details to compare | Reason for checking |
|---|---|---|
| Brake friction and discs | Friction formulations and iron, composite or application-specific disc construction | Use an approved matched application; material affects heat behaviour, wear, noise and bedding. |
| Suspension and steering | Steel, aluminium, rubber, hydraulic bushes and engineered polymers | Material alone does not prove interchangeability; geometry, stiffness and joint design must match. |
| Seals, hoses and belts | Application-specific elastomers, reinforced rubber and thermoplastics | Fluid, temperature and pressure compatibility matters more than appearance or colour. |
| Filters | Cellulose, synthetic or combined media with rubber or moulded seals | Match housing, dimensions, flow direction, filtration specification and seal arrangement. |
| Electrical components | Copper conductors, electronic sensing elements, sealed housings and defined connector systems | Pinout, calibration, temperature range and environmental sealing must suit the exact position. |
BMW X5 (E70) M 4.4L 555 hp is already narrowed to an exact engine and power entry, but material or construction wording still cannot replace the application. Compare the installed reference, dimensions, mounting points, connector, axle or side and any option note. Drive layout, axle load, wheel and tyre specification and any adaptive or self-levelling chassis equipment can divide parts that otherwise look alike. Treat front and rear axle applications as separate checks.
Fault symptoms and urgency
| Symptom | Possible areas | Action |
|---|---|---|
| Grinding, strong pulling or major brake vibration | Friction parts, calipers, hoses, hubs, bearings or tyres | Stop using the vehicle if braking is impaired and arrange immediate inspection. |
| Red temperature warning, steam or rapid coolant loss | Leak, pump, thermostat, fan, radiator, tank or hose | Stop safely, switch off and do not open the hot system. |
| Heavy steering, sudden play or fluid loss | Steering joints, rack, assistance system, hoses or tyres | Inspect urgently and do not continue if control is affected. |
| Misfire or flashing engine warning | Ignition, fuelling, intake, wiring, sensor or mechanical condition | Reduce load and diagnose promptly; continued use can damage other systems. |
| Knocking or unstable handling | Arms, bushes, links, springs, dampers, mounts or bearings | Inspect promptly and correct mechanical faults before alignment. |
| Charging warning or repeated flat battery | Battery, alternator, belt, wiring, grounds or parasitic load | Test the complete charging system before replacing parts. |
Maintenance and repair workflow
- Record the VIN, production month, installed reference, symptoms and diagnostic evidence.
- Confirm M, 555 hp, 4,395 cc and the X5 (E70) body series.
- Review product exclusions, production splits, equipment restrictions and supersessions.
- Inspect connected components and identify the cause of the original fault.
- Fit with suitable tools, clean working methods, new seals and the stated torque procedure.
- Complete required bleeding, alignment, coding, adaptation or calibration.
- Verify levels, leaks, warning lamps, noise and safe operation before normal road use.
Common mistakes to avoid
- Choosing from the model and engine description without confirming the exact engine and power output.
- Using a photograph, diameter or connector as the only fitment check.
- Ignoring axle, side, steering position, gearbox, driven wheels or production-date notes.
- Mixing fluids by colour or broad universal wording instead of approval.
- Replacing a sensor without testing wiring, supply voltage and the related mechanical system.
- Fitting a new component without correcting contamination, overheating, low voltage or misalignment that caused the failure.
- Skipping alignment, bleeding, coding or calibration after a repair that requires it.
UK MOT, legal and safety notes
The UK MOT checks relevant braking, steering, suspension, tyre, lighting, visibility, restraint and emissions items, but it is not a substitute for servicing or a complete compatibility inspection. A component can be worn, leaking or near its limit without an MOT pass guaranteeing future condition. Complete required calibration and verify safe operation after repair.
Lighting, suspension, wheel, exhaust and performance modifications can affect road legality, insurance, clearance and handling. Use components suitable for road use and complete any required coding or calibration. Safety-critical, refrigerant, restraint, high-current electrical and high-voltage work should be handled or checked by a suitably competent technician.
BMW X5 (E70) M 4.4L 555 hp FAQs
Q: Is this page for every M?
A: No. It is specific to 555 hp, 4,395 cc and the stated production period.
Q: Are the category links already vehicle-filtered?
A: Yes. Each destination retains this exact vehicle selection.
Q: Can registration lookup be used alone?
A: Use it as a starting point, then confirm the VIN, build details and product-specific notes.
Q: Are product photographs final fitment proof?
A: No. Match the complete application, reference, dimensions, connections and technical notes.
Q: Why can two variants with the same power need different parts?
A: Capacity, engine family, production revision, emissions equipment, gearbox and factory options can differ.
Q: Should diagnostic codes be cleared before testing?
A: No. Save codes and operating context first, then test the affected system.
Q: Does an MOT pass confirm every service item?
A: No. It does not verify complete maintenance, fluid specifications or every compatibility detail.
Q: When should the vehicle not be driven?
A: Stop for impaired brakes or steering, serious fluid leaks, overheating, severe looseness or red safety warnings.
Q: Can a universal fluid be used?
A: Only when it explicitly meets the exact approval and procedure required for the assembly.
Q: When is professional fitting advisable?
A: Use a suitably competent technician for safety-critical, refrigerant, fuel, restraint, coding, calibration or high-voltage work.
