7 Products
Your Current Vehicle
Or
Select Your Vehicle
What an ABS sensor measures
The wheel-speed sensor converts rotation into an electrical signal. The ABS controller compares wheel acceleration and deceleration many times per second. When one wheel slows more rapidly than vehicle behaviour permits, hydraulic valves can reduce and reapply pressure to preserve steering control.
Wheel speed is also a foundational data source. Stability control compares it with steering angle, yaw and lateral acceleration; traction control uses it to detect driven-wheel spin. One faulty signal can therefore disable several apparently unrelated features.
From rotating encoder to control action
- A toothed or multipole encoder rotates with the wheel or driveshaft.
- Changing magnetic conditions pass the stationary sensing element.
- The sensor produces an analogue waveform or digitally switched current/voltage.
- Wiring carries the signal to the ABS electronic control unit.
- Software checks frequency, direction where available, plausibility and change rate.
- Hydraulic modulation occurs if impending lock is detected during braking.
- Fault monitoring stores diagnostic information when a circuit or signal is implausible.
Sensor technologies compared
| Technology | Signal behaviour | Diagnostic implications |
|---|---|---|
| Passive inductive | Generates AC voltage whose frequency and amplitude rise with speed. | Resistance and waveform can be tested, but low-speed output may be small. |
| Hall-effect active | Powered sensor switches a digital signal as magnetic poles pass. | Requires supply and ground checks; resistance tests may mislead or damage it. |
| Magnetoresistive active | Changes electrical response with magnetic field and can read very low speed. | Often uses current modulation; vehicle-specific test data is essential. |
| Direction-sensitive active | Encodes rotation direction as well as speed. | Incorrect orientation or substitute technology can cause plausibility faults. |
| Integrated hub sensor | Sensing and encoder geometry are designed within hub/bearing assembly. | Hub play, internal damage or bearing orientation can be the true cause. |
| Combined vehicle-speed source | Wheel signals are shared over networks to other modules. | A local ABS fault can affect speedometer, gearbox or assistance systems. |
Encoders and air gap
An exposed reluctor ring uses teeth and gaps to vary magnetic reluctance. A multipole ring contains alternating magnetic poles in a rubberised or metal carrier, often forming one bearing seal. Damage as small as one cracked tooth or weak magnetic pole can create a repeating signal dropout at a particular wheel position.
The sensor-to-encoder gap must remain within design limits. Rust beneath a sensor raises it; wheel-bearing play varies it dynamically; impact damage can make contact. Many active designs do not have a manually adjustable gap, so clean seating and correct parts establish it.
System performance factors
- Encoder integrity: every tooth or magnetic pole must be present and evenly spaced.
- Mount cleanliness: corrosion must not tilt or lift the sensor.
- Bearing condition: play alters gap and can damage the encoder.
- Harness routing: steering and suspension travel must not stretch or rub the lead.
- Electrical supply: active sensors need correct voltage and circuit loading.
- Signal interpretation: test equipment must suit current-modulated and digital designs.
- Tyre consistency: substantial rolling-radius differences can create plausibility concerns.
Components and locations
Sensing head and mounting flange
The moulded head positions the electronic element close to the encoder. Its O-ring or shaped flange may seal a hub opening. Forcing a seized sensor out can leave fragments or damage the bore.
Harness, connector and retainers
Flexible cable must survive wheel movement, stone impact and heat. Original clips define a safe curve; tying it to a brake hose or leaving excess cable loose is unsafe. Connector seals keep water away from small terminals.
Reluctor ring or magnetic bearing seal
Reluctors may be pressed onto CV joints or integrated with hubs. Magnetic seals have a working face that must point towards the sensor. Installing a wheel bearing backwards can produce no usable signal even though the bearing fits perfectly.
ABS control and hydraulic unit
The controller powers sensors, interprets signals and drives solenoid valves and pump. A stored wheel-sensor code identifies a circuit or plausibility area; it does not prove that the removable sensor is defective.
Materials and environmental protection
| Part | Construction purpose | Failure mode |
|---|---|---|
| Moulded polymer head | Encapsulates electronics and fixes geometry. | Cracks admit moisture or release the mounting flange. |
| Copper conductor | Carries supply and low-level signal. | Internal strands break after repeated flexing. |
| Sealed connector | Protects terminals from spray and salt. | Damaged seals, fretting or corrosion raise resistance. |
| Steel reluctor | Provides durable magnetic teeth. | Rust expansion cracks rings or changes tooth profile. |
| Elastomer magnetic ring | Stores alternating poles in compact bearing seal. | Impact, metal debris and incorrect cleaning weaken signal. |
| Stainless/plated fixing | Retains sensor accurately. | Seizure, wrong bolt length or excessive torque damages housing. |
Selecting the correct sensor
| Check | Possible variation | Confirmation |
|---|---|---|
| Axle and side | Harness length, connector and clip positions. | Catalogue handing and physical route. |
| Sensor principle | Passive, active voltage or active current output. | OE reference and wiring information. |
| Hub/bearing design | Exposed teeth or integrated magnetic encoder. | Inspect installed assembly and part data. |
| Production date | Connector or controller generation. | VIN and build date. |
| Cable protection | Grommets and sleeves suit different knuckles. | Compare all retainers before fitting. |
| Mounting geometry | Insertion depth and flange angle set air gap. | Dimensional drawing and original sensor. |
Electrical specifications and test methods
There is no universal resistance or voltage value. A passive coil may show measurable resistance, while an active semiconductor can appear open, directional or be harmed by an inappropriate meter test. Use the vehicle circuit diagram, specified breakout method and a suitable oscilloscope or scan tool.
Back-probing must not spread sealed terminals. Measuring supply with the connector unplugged may miss a circuit that collapses under load. Current-clamp or series-resistor methods for two-wire active sensors require technical data and care to avoid controller damage.
Diagnosis in a logical order
- Record all module faults and freeze-frame conditions before clearing anything.
- Compare live wheel speeds from rest through a slow controlled movement.
- Inspect tyres, bearing play, sensor seating, cable route and connector condition.
- Examine the complete encoder circumference, using magnetic viewing film where appropriate.
- Check supply, ground and signal according to the exact sensor technology.
- Wiggle the harness while monitoring for intermittent dropouts.
- Compare oscilloscope waveforms side to side at equal speed.
- After repair, confirm consistent data and completion of the controller self-test.
Symptoms and urgency
| Symptom | Possible cause | Response |
|---|---|---|
| ABS and stability lamps | Sensor circuit, encoder, voltage or controller fault. | Drive cautiously only if basic braking is normal and arrange diagnosis. |
| ABS activates near a stop | Weak low-speed signal from rust, gap or cracked ring. | Inspect promptly; stopping feel can be disturbed. |
| One speed drops to zero | Signal interruption, missing tooth/pole or wiring break. | Compare waveform and encoder before replacing parts. |
| Speedometer inoperative | Some vehicles derive road speed from ABS data. | Scan the network and restore the wheel-speed source. |
| Warning after bearing replacement | Bearing reversed, encoder damaged or sensor gap altered. | Recheck bearing orientation and part specification. |
| Wheel bearing loose/noisy | Mechanical wear affecting encoder position. | Repair urgently; bearing failure is a separate safety risk. |
Replacement and installation
Disconnect electrical power only where the service procedure requires it. Release harness retainers before removing the sensing head, clean corrosion from the mounting face without enlarging the bore and keep abrasive debris out of the bearing. Do not apply grease between a sensor and mount unless an approved product is specified.
Route the new lead exactly, turn steering from lock to lock and check full suspension movement for strain. Use the correct fixing torque. If a magnetic bearing is replaced, identify the encoder side before pressing and apply force only through the proper race.
Common mistakes to avoid
- Replacing the sensor because a code mentions its wheel.
- Testing every sensor with an ohmmeter regardless of technology.
- Ignoring rust that lifts the sensing head away from the ring.
- Installing a magnetic wheel bearing with its encoder facing away.
- Striking or scraping a magnetic ring with steel tools.
- Routing cable outside its clips or around a brake hose.
- Using wheel speed from a lifted spinning wheel without safe support.
- Assuming identical tyre labels guarantee equal rolling circumference.
- Clearing codes without checking that the self-test passes.
- Driving normally when ABS and stability assistance are unavailable.
Maintenance, modifications and UK MOT
Sensors need no routine lubrication. Protect wiring during brake, bearing, driveshaft and suspension work, and clean magnetic debris only with safe methods. Non-standard hubs, extreme wheel offsets and mismatched tyres can affect encoder alignment or plausibility; modifications must preserve braking-system function.
ABS warning-lamp operation is assessed during the UK MOT where the system is required. A lamp indicating a malfunction can cause failure. Mechanical braking may still work, but anti-lock, stability and related assistance may be disabled, so legal test status should never replace prompt diagnosis.
ABS sensor FAQs
Q: Does an ABS code prove the sensor is faulty?
A: No. Wiring, encoder, bearing, supply and mounting faults can set the same code.
Q: Can I drive with the ABS light on?
A: Basic braking may remain, but safety assistance can be disabled; drive cautiously only to arrange prompt repair.
Q: Why does ABS operate at very low speed?
A: One weak signal may drop out early because of excessive gap, rust or encoder damage.
Q: Are front and rear sensors interchangeable?
A: Usually not; electrical type, mounting and harness routing commonly differ.
Q: Can a wheel bearing cause an ABS fault?
A: Yes. Play, an integrated damaged encoder or reversed installation can corrupt speed data.
Q: How is a magnetic encoder identified?
A: Service data or magnetic viewing film can reveal the pole side without damaging it.
Q: Can metal filings affect the sensor?
A: Debris can distort the magnetic field and should be removed carefully.
Q: Why is resistance testing unreliable?
A: Active sensors contain electronics rather than a simple coil and need powered signal tests.
Q: Must a new ABS sensor be coded?
A: Most wheel sensors do not, but some vehicles need fault clearing or calibration procedures.
Q: Can different tyre sizes trigger faults?
A: Significant rolling-radius differences can create implausible relative speeds.
Q: Should grease be applied to the sensor?
A: Only an approved product where specified; excess material can alter seating or collect debris.
Q: Will an ABS warning fail an MOT?
A: A malfunction indication on a required system can cause failure.
Q: Why did a fault appear after brake work?
A: The lead may be stretched, a connector left open or metal debris moved near the encoder.