20 Products
Your Current Vehicle
Or
Select Your Vehicle
Shop All Bulbs by Brand
Only manufacturers with matching products in the current catalogue are shown.
All Bulbs for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for All Bulbs
Popular model families are ranked by the number of matching catalogue products.
Related Categories for All Bulbs
Explore related part types from the same catalogue group.
How vehicle lamps create usable light
A bulb is only one part of an optical system. Its luminous element sits at a precise point relative to a reflector, shield or projector lens. Small positional errors spread light into glare and dark areas even when total output is high.
Exterior lighting also communicates. Indicators, brake lamps and position lamps need defined colour, intensity and distribution so other road users can interpret them quickly. Electrical compatibility and optical compatibility are equally important.
From electrical command to road illumination
- A switch or control module requests a lighting function.
- A fused circuit, relay or electronic driver supplies controlled power.
- The filament, arc or semiconductor converts energy into light and heat.
- The base locates the source at the lamp's designed focal position.
- Reflector, shield and lens shape the beam or signal pattern.
- Monitoring electronics may measure current or circuit status.
- Heat leaves through the bulb, holder, housing and ventilation path.
Light-source technologies
| Technology | How it works | Compatibility focus |
|---|---|---|
| Tungsten filament | Current heats a wire until it glows. | Voltage, wattage, base and filament positions. |
| Halogen | Quartz capsule and halogen gas support hotter filament operation. | Do not touch glass; exact focus and approved wattage matter. |
| HID/xenon | Ballast creates an arc through gas and metal salts. | Capsule family, ballast, igniter and approved lamp system. |
| Replaceable LED bulb | Semiconductor chips emit light through driver electronics. | Optics, polarity, cooling, monitoring and road approval. |
| Integrated LED module | LED board and heat sink form part of the lamp assembly. | Often not serviced as a conventional bulb. |
| Dual-filament bulb | Two filaments provide separate low/high or tail/brake functions. | Offset pins and contact orientation prevent interchange. |
Light output, colour and heat
- Lumens: describe total light, not beam quality.
- Candela: describes intensity in a direction.
- Colour temperature: influences appearance, not automatically visibility.
- Spectral output: affects colour rendering and weather perception.
- Power consumption: determines circuit and thermal load.
- Source geometry: establishes focus in the optical system.
- Thermal path: controls filament, LED chip and driver life.
Bases and functions
| Base/function group | Typical feature | Common error |
|---|---|---|
| Headlamp flange base | Keyed metal/plastic flange fixes filament orientation. | Bulb not fully seated beneath retaining spring. |
| Bayonet base | Side pins lock into holder with one or two contacts. | Forcing level pins into offset-pin holder. |
| Wedge base | Glass or plastic wedge contacts holder directly. | Wrong width, thickness, wattage or polarity. |
| Festoon | Tube with contacts at both ends. | Incorrect length strains holder or gives poor contact. |
| HID capsule base | Precisely keyed ceramic/plastic base and high-voltage connection. | Mixing capsule families or unsafe ballast handling. |
| LED module connector | Dedicated multi-pin driver or lamp connection. | Assuming a serviceable bulb exists. |
Construction and materials
Filament and support
Tungsten tolerates very high temperature. Support wires position the filament accurately despite vibration. Evaporated tungsten eventually darkens glass and weakens the filament.
Quartz and glass envelopes
Halogen quartz operates at high temperature and pressure. Skin oils create local hot spots. Conventional glass bulbs run cooler but still need clean handling and correct ventilation.
LED chips and driver
LED junctions are efficient but temperature-sensitive. Heat sinks move heat away; fans and drivers add failure modes. A cool-looking front lens does not mean the electronics are within limits.
Contacts, seals and holders
Plated terminals carry current while seals exclude moisture. Loose contacts create resistance and heat that melts holders. Bulb replacement alone will not restore damaged spring pressure.
Material and failure comparison
| Part/material | Benefit | Failure concern |
|---|---|---|
| Tungsten filament | Accurate compact incandescent source. | Evaporation, vibration and overvoltage break it. |
| Fused quartz | Withstands high halogen temperature. | Fingerprints and scratches cause hot spots. |
| Ceramic HID base | Insulates high voltage and heat. | Cracks and contamination affect arc position. |
| Semiconductor LED | Efficient long-life light in controlled conditions. | Heat and overcurrent degrade output. |
| Aluminium heat sink | Conducts heat from LED board. | Restricted airflow and poor contact raise temperature. |
| Plated contacts | Low-resistance removable connection. | Corrosion and weak spring force create heating. |
Selecting the correct bulb
| Check | Possible variation | Evidence |
|---|---|---|
| Lighting function | Dipped, main, fog, indicator, brake or interior. | Handbook and lamp-unit labels. |
| Vehicle build date | Facelift lamp or LED-module revision. | VIN-derived production date. |
| Base code | Keys, pins, contacts and focal position. | Existing reference and holder. |
| Voltage/wattage | Circuit and thermal load. | Manufacturer specification. |
| Colour | White, amber or red legal function. | Lamp design and approval. |
| Control system | Direct supply, ballast, LED driver or monitoring. | Wiring and diagnostic equipment list. |
Electrical diagnosis
- Confirm every failed function and whether both sides are affected.
- Inspect the bulb, holder, fuse, connector, earth and lamp for moisture.
- Measure voltage at the bulb under load, not only with it disconnected.
- Check earth voltage drop and charging-system voltage.
- Scan body or lighting modules where circuits are electronically controlled.
- Compare commanded status, fault codes and actual output.
- Repair melted holders and water ingress before installing another bulb.
- After fitting, check all functions, warnings and beam aim.
Fault signs and response
| Symptom | Possible cause | Response |
|---|---|---|
| Repeated bulb failure | Overvoltage, vibration, moisture or poor contact. | Diagnose the circuit and lamp, not just the bulb. |
| Melted holder | High resistance, wrong wattage or poor terminal force. | Repair before heat damages wiring or housing. |
| Rapid indicator flash | Failed lamp or load mismatch. | Restore correct function and monitoring. |
| Poor headlamp pattern | Bulb mis-seated, wrong source or damaged optics. | Correct fit and check beam aim. |
| Flickering HID/LED | Ballast, driver, voltage, thermal or connector fault. | Use safe diagnostic procedures. |
| Condensation/water | Vent or seal fault in lamp unit. | Correct water entry before replacement. |
Installation safety
Switch lamps off and let them cool. Some HID systems generate dangerous starting voltage; follow isolation instructions and do not work on damaged high-voltage connectors. Tight access can tempt blind forcing, so use a mirror or remove approved access panels.
Hold halogen bulbs by the base or clean gloves. Align keys before securing clips or caps. Ensure rubber covers seal so dust and water stay out. LED heat sinks and fans need designed clearance; do not trap wiring against them.
Common mistakes
- Choosing a bulb because the base appears to fit.
- Touching halogen quartz with bare fingers.
- Installing a higher-wattage bulb in standard wiring and optics.
- Fitting an LED retrofit without checking beam pattern and approval.
- Forcing offset bayonet pins.
- Leaving headlamp dust covers open.
- Ignoring melted holders and weak earths.
- Handling HID wiring without high-voltage precautions.
- Assuming a brighter colour temperature improves wet-road vision.
- Failing to check beam aim after replacement.
Upgrades, UK MOT and road legality
Approved upgrade bulbs must retain the specified base, wattage and optical position. HID or LED conversions in filament-designed headlamps can produce glare and may not meet legal or MOT requirements. Complete approved lamp systems can require levelling and cleaning equipment according to their specification.
Older lamp units also lose performance through reflector corrosion, lens abrasion and internal haze. Installing a more intense bulb cannot restore damaged optics and may increase glare. Clean external lenses with methods appropriate to their coating, repair failed vents and seals, and replace structurally damaged lamps. Beam-setting equipment should be used after housing, suspension or ride-height work affects aim.
The UK MOT checks operation, colour, condition, security and aim of relevant lamps. Warning functions and inappropriate light sources may also matter. Lighting rules apply between tests, so failed brake, indicator or headlamp functions should be repaired immediately.
Vehicle bulb FAQs
Q: How do I identify the correct bulb?
A: Use vehicle data, function, lamp markings, base code, wattage and existing reference.
Q: Can a higher-wattage bulb be fitted?
A: No unless the complete lamp and circuit are approved for it.
Q: Why should halogen glass not be touched?
A: Skin oils create local hot spots that shorten life.
Q: Are LED retrofit bulbs road legal?
A: Legality depends on lamp approval and application; physical fit is not enough.
Q: Why does a new bulb not work?
A: Check fuse, supply, earth, holder, monitoring and correct seating.
Q: Should headlamp bulbs be replaced in pairs?
A: It can help balance colour and output where both have similar age.
Q: What causes rapid indicator flashing?
A: A failed bulb or incorrect electrical load is common.
Q: Can HID bulbs be changed safely at home?
A: High starting voltage demands the manufacturer's isolation procedure and suitable competence.
Q: Why do bulbs fail repeatedly?
A: Charging overvoltage, vibration, water or hot connectors should be checked.
Q: Does a blue-white bulb improve visibility?
A: Appearance alone does not prove useful beam output, especially in rain.
Q: Can an error-cancelling resistor be added?
A: Resistors create heat and do not make an incompatible retrofit optically or legally correct.
Q: Why is the beam poor after replacement?
A: The bulb may be mis-seated, wrong, or the optics and aim may be damaged.
Q: Will a failed bulb fail the MOT?
A: Required lighting functions, colour and aim are assessed and can cause failure.