33 Products
Your Current Vehicle
Or
Select Your Vehicle
Shop Suspension Arms by Brand
Only manufacturers with matching products in the current catalogue are shown.
Suspension Arms for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for Suspension Arms
Popular model families are ranked by the number of matching catalogue products.
Related Categories for Suspension Arms
Explore related part types from the same catalogue group.
Suspension arms define where the wheel may move
An arm carries force between knuckle and structure while its joints permit selected rotation. Several arms can constrain six possible directions with deliberate compliance.
The position of each pivot determines geometry throughout suspension travel. Small dimensional errors change toe, camber and steering behaviour.
Arm and link types
| Type | Geometry role | Common joints | Typical load |
|---|---|---|---|
| Lower wishbone/control arm | Locates lower knuckle in two axes. | Two bushes and ball joint. | Braking, cornering and road impact. |
| Upper control arm | Sets upper knuckle path/camber. | Bushes and upper ball joint. | Lateral and vertical location. |
| Trailing arm | Controls fore-aft wheel position. | Large body bush and hub mounts. | Braking and longitudinal impact. |
| Toe link | Sets rear wheel toe. | Ball joints/bushes and adjuster. | Lateral steering force. |
| Camber/lateral link | Controls side position/camber curve. | Inner bush and outer joint. | Cornering load. |
| Tension/compression strut | Controls caster and braking reaction. | Large compliant bush and ball joint. | Longitudinal force. |
Wishbone and multi-link layouts
More links separate functions but add diagnostic interfaces
A wishbone combines multiple load directions in one structure. Multi-link suspension gives designers more independent control of compliance and wheel path.
One worn link in a multi-link axle can steer the wheel only under braking or cornering. Static hand checks may miss its loaded movement.
Arm materials
| Material/process | Benefit | Damage pattern | Repair principle |
|---|---|---|---|
| Pressed/welded steel | Efficient hollow form and controlled deformation. | Corrosion, crease or seam damage. | Replace if strength/geometry is uncertain. |
| Forged steel | High toughness in compact section. | Bend, impact mark or corrosion pitting. | Do not heat-straighten casually. |
| Cast aluminium | Low unsprung mass and complex shape. | Crack or brittle impact fracture. | Usually replace, not weld/straighten. |
| Forged aluminium | Light with favourable grain flow. | Hidden crack or distorted bore. | Inspect with approved method. |
| Composite/specialist arm | Tailored stiffness and mass. | Delamination or fibre damage. | Vehicle-specific replacement rules. |
Rubber and hydraulic bushes
Bonded rubber allows angular motion by torsion, not by sliding. Voids tune stiffness differently fore-aft and laterally.
Hydraulic bushes contain fluid chambers to control certain frequencies. Leakage, separation or incorrect orientation changes braking and steering compliance.
Ball joints
A spherical stud articulates in a low-friction socket, protected by a grease-filled boot. Some joints carry spring load; others mainly locate.
Test at the suspension position specified so load does not hide or create apparent play. A torn boot accelerates contamination even before looseness develops.
Part identification
Use VIN and suspension option, then confirm exact arm role, side and axle. Compare casting/stamping number and every bracket.
Check inner bolt diameter, bush width, ball-joint taper, arm length and any alignment eccentric. Do not infer handedness from photographs alone.
Symptoms and alternatives
| Symptom | Arm-related possibility | Alternative |
|---|---|---|
| Clunk braking/accelerating | Fore-aft bush separation or loose pivot. | Brake movement, mount or subframe. |
| Steering pull changes on braking | Control-arm compliance differs side to side. | Brake imbalance or tyre conicity. |
| Rear steer sensation | Toe-link bush/joint movement. | Tyre, bearing or subframe fault. |
| Uneven tyre wear | Geometry shift from arm/bush damage. | Pressure, alignment adjustment or wheel. |
| Knock over one-wheel bumps | Ball joint or arm bush. | Anti-roll link, damper or loose trim. |
| Alignment outside range | Bent/wrong arm or displaced bush. | Knuckle, subframe or body damage. |
Visual bush inspection
Look for rubber separation from sleeve, tears across load-bearing webs, fluid leakage and excessive off-centre position. Surface crazing alone may be less significant.
Apply only controlled leverage and compare movement to a known sound joint or data. Do not tear a good bush with an oversized pry bar.
Joint play inspection
Support the suspension as specified and observe the joint directly while movement is applied. Tyre sidewall and rubber compliance can imitate clearance.
Measure where a limit exists. Any unsafe attachment, fracture or movement affecting control requires immediate action.
Impact and pothole damage
A severe impact can bend an arm, knuckle, subframe and wheel together. Compare wheelbase, track, ride height and alignment on both sides.
Do not pull mounting holes into place with bolts. Measure body and subframe datums, then restore every damaged component.
Corrosion assessment
Surface rust can be cleaned for evaluation; scaling, perforation and thinning near welds or bush eyes threaten load capacity.
Do not conceal corrosion under thick coating before judging it. Replace an arm when remaining strength cannot be proven.
Safe lifting and stored energy
The arm may be carrying spring force even when the wheel hangs
Determine where the spring seats and whether the arm supports it. Restrain or unload the spring with the specified fixture before pivot removal.
Air and hydraulic suspension can self-level. Select service mode, depressurise where required and prevent controller wake-up.
Hub, driveshaft and brake support
Support the knuckle so a released arm cannot pull the driveshaft joint, brake hose or sensor loom. Remove caliper or shaft only where the procedure requires.
Never suspend a caliper from its hose. Record clip routing and check clearance at full steering and travel afterwards.
Separating a ball-joint taper
Remove the nut as directed and use a suitable puller/separator on designed surfaces. Protect the boot if it will remain in service.
Do not heat aluminium knuckles, strike threaded studs or lever against brake shields. Renew damaged nuts and joints.
Removing pivot bolts
Mark alignment-cam positions for reference, but plan a full alignment. Support the arm and remove bolts without trapping fingers.
Seized bolts can bond to inner sleeves. Use a controlled cutting/removal plan that protects body, fuel, brake and electrical systems.
Bush replacement versus complete arms
Separate bushes can be economical when the arm and joint are sound and the manufacturer permits pressing. Correct fixtures support the eye without distortion.
Complete arms reduce assembly variables but still need exact bush and joint specification. Inspect their preinstalled orientation before fitting.
Pressing bushes
Record insertion depth and angular marks. Press on the correct outer sleeve while supporting the arm close to the bore.
Do not lubricate with mineral products unless specified, and never press through bonded rubber. Confirm no arm cracks or bore enlargement afterwards.
Installation and fasteners
| Joint | Installation control | Failure prevented |
|---|---|---|
| Inner bonded bush | Correct index; final torque at stated height. | Preload and early tearing. |
| Ball-joint taper | Clean seat, new nut and exact torque. | Movement or stud damage. |
| Alignment eccentric | Washers seated and marks initially preserved. | Slip and gross geometry error. |
| Subframe mount | Sound threads and one-time bolt rules. | Safety-critical insecurity. |
| Sensor/hose bracket | Original clip and movement clearance. | Chafe or warning fault. |
| Spring seat arm | Spring indexed and load released gradually. | Dislodgement or stored-energy release. |
Ride-height tightening
Set the hub-to-body dimension or load condition specified, then tighten bonded-bush pivots. This establishes neutral rubber torsion.
Do not crawl beneath a vehicle supported unsafely to achieve loaded height; use a lift, ramps or approved support fixture.
Wheel alignment and calibration
Set tyre pressure and ride height, settle the suspension and measure all four wheels. Adjust designed cams/links only.
Calibrate steering angle, ride-height sensors and relevant driver-assistance systems after geometry work when required.
Post-repair verification
Check fastener witness marks, boots, clips and clearance through steering/suspension motion. Confirm no spring or hose is displaced.
Road-test progressively for pull, noise and stability, then re-inspect. Any new looseness means stop and diagnose immediately.
Common mistakes
Errors include ordering the wrong link, forcing holes into alignment, tightening bonded bushes at full droop and reusing self-locking fasteners.
Others are unrestrained spring force, damaged tapers, misindexed void bushes, skipped alignment and welding or straightening an unapproved arm.
UK MOT and safety context
Current MOT inspection assesses suspension arms, joints, pins and bushes for fractures, insecurity, excessive wear and unsafe modification. Serious loss of attachment can be dangerous.
Do not drive with a cracked or severely corroded arm, loose fixing, excessive ball-joint play or unstable wheel geometry. Arrange safe recovery and competent repair.
Practical suspension-arm FAQs
Q: Is every suspension arm a wishbone?
A: No; trailing, toe, camber and tension links perform different roles.
Q: Can I replace only a bush?
A: Yes where approved and the arm/joint/bore remain sound.
Q: Why tighten bushes at ride height?
A: It prevents excessive bonded-rubber twist in normal use.
Q: Can an aluminium arm be straightened?
A: Replace it unless a specific approved repair proves otherwise.
Q: Does torn rubber always mean excessive play?
A: Assess load-bearing separation and measured movement by the stated criteria.
Q: Why does braking change steering pull?
A: A compliant arm bush can let toe or caster shift under force.
Q: Can alignment compensate for a bent arm?
A: No; restore sound geometry before adjustment.
Q: Must ball-joint tapers be greased?
A: Follow the exact instruction; many rely on clean dry friction.
Q: Can a hanging wheel unload every joint?
A: No; spring layout can keep certain joints loaded.
Q: Why replace pivot bolts?
A: Some are self-locking or torque-to-yield and designated one use.
Q: Should impact damage trigger body measurement?
A: Yes; arm, knuckle, subframe and structure can move together.
Q: Is wheel alignment required?
A: Measure the complete geometry after arm or link replacement.
Q: What confirms a safe repair?
A: Secure indexed joints, correct ride-height torque and verified alignment.