0 Products
No products found
Use fewer filters or
Your Current Vehicle
Or
Select Your Vehicle
Shop Wiper motor by Brand
Only manufacturers with matching products in the current catalogue are shown.
Wiper motor for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for Wiper motor
Popular model families are ranked by the number of matching catalogue products.
Related Categories for Wiper motor
Explore related part types from the same catalogue group.
The motor creates torque and controls the end of every wipe
A compact DC motor turns much faster than the blades need. Worm or gear reduction lowers speed and multiplies torque before an output crank moves the linkage. The geometry converts continuous rotation into a reversing sweep at each spindle.
Parking is a separate requirement from running. A switch or electronic sensor continues or commands operation after the stalk is switched off until the mechanism reaches its calibrated rest position.
Motor and control arrangements
| Arrangement | Control method | Application feature | Diagnostic concern |
|---|---|---|---|
| Conventional two-speed motor | Separate brush circuits selected by relay/stalk. | Single motor drives mechanical linkage. | Supply path, brushes and park switch. |
| Module-controlled motor | Body controller switches relays or solid-state output. | Intermittent and wash-wipe logic integrated. | Command data and output load capability. |
| Networked smart motor | Power, ground and LIN/CAN communication. | Position and speed managed electronically. | Coding, communication and calibration. |
| Dual front motors | Synchronised electronic drive. | Each arm can have a dedicated motor. | Left/right identity and synchronisation. |
| Rear motor | Local park switch or module control. | Often drives blade directly through tailgate. | Spindle seizure and flexible-harness breaks. |
Electric motor and reduction gearbox
Armature, magnets and brushes
Current through armature windings creates torque against permanent magnets. Carbon brushes transfer current to the rotating commutator. Wear, water entry and overheated windings reduce output or create dead positions.
Gear reduction and crank output
A worm commonly drives a large moulded or metal gear. Grease controls wear and noise. The output pin or crank must match the linkage radius and angular datum exactly to produce the intended sweep.
Park-switch operation
Traditional motors contain a conductive track and moving contacts in the gear cover. When the driver switches off, the circuit remains supplied through the park path until the gear reaches its insulated segment. Incorrect wiring can defeat dynamic braking and allow the mechanism to coast beyond park.
Smart motors report position electronically and may learn end points. They can protect themselves from blockage, but repeated obstruction by ice or seized pivots still overheats the motor and stresses linkage parts.
Compatibility checks
| Selection point | Possible variation | Result if mismatched |
|---|---|---|
| Front/rear and vehicle side | Different spindle, bracket and control. | Cannot drive or park the intended mechanism. |
| Drive position | RHD and LHD linkage sweep geometry. | Wrong wiped area or arm collision. |
| Output crank | Length, taper, spline and clocking. | Incorrect arc and high linkage load. |
| Connector/pinout | Direct speeds, park contacts or network line. | Electrical damage or missing functions. |
| Mounting points | Bushes, bracket and isolation geometry. | Vibration, misalignment or no fit. |
| Control generation | Relay-controlled versus smart motor. | Communication faults and no operation. |
| Park calibration | Crank rest angle and software end position. | Blades stop on screen or below scuttle. |
Linkage and spindle load
The motor is designed to overcome wet-blade friction and normal linkage resistance. Corrosion can enter spindle bushes and gradually raise torque demand. The driver may notice slower wiping before the motor fuse opens or plastic linkage sockets fail.
Disconnect the linkage only where the procedure allows and move pivots by hand to compare resistance. A new motor should not be used to force a seized mechanism. Replace or correctly overhaul the linkage first.
Electrical control path
Depending on design, the stalk may carry motor current, signal a relay, send resistor-coded inputs or communicate with a body module. Rain sensors and vehicle-speed logic can modify intermittent timing. Use live input and output data to identify whether the command reaches the controller.
Check fuses by voltage on both sides under the fault condition. A fuse that has opened indicates excessive current or a short and should not simply be replaced with a higher rating.
Voltage-drop and current diagnosis
| Test result | Likely direction | Next check |
|---|---|---|
| Low voltage at motor under load | Resistance in supply relay, fuse, connector or wire. | Section-by-section positive voltage drop. |
| High voltage on motor ground | Poor earth connection. | Ground drop to battery negative. |
| High current and slow sweep | Seized linkage or motor mechanical/electrical drag. | Separate motor from linkage safely. |
| Low current with no movement | Open winding, worn brush or control not fully applied. | Waveform and direct circuit specification. |
| Normal motor sound, stationary arms | Disconnected socket, stripped gear or loose crank. | Physical drive inspection. |
| Fuse opens immediately | Short circuit, jammed motor or wrong wiring. | Resistance/isolation and mechanical obstruction. |
Current waveform information
A current clamp can show repeating commutator segments as the motor rotates. Missing or uneven humps can indicate a damaged commutator or armature section. Slowly rising current during a sweep may instead reveal changing mechanical load.
Compare against known-good data and the specified mode. Blade friction, screen wetness and temperature affect current, so reproduce conditions carefully and never test for long on a dry windscreen.
Failure-to-park diagnosis
If blades stop immediately wherever the switch is released, the park supply, internal contact or control logic may be absent. If they continue indefinitely, a shorted park contact or missing position recognition is possible. Incorrect crank timing can park the motor correctly while leaving blades in the wrong place.
Do not reposition arms on their splines until motor park has been proved. Otherwise the linkage may travel below the scuttle or force blades into the windscreen pillars.
Front versus rear wiper faults
Front mechanisms frequently suffer corroded pivots beneath the scuttle. Drain blockage can immerse motors or connectors. Rear motors are exposed to water through spindle seals and to wiring fatigue where the tailgate loom bends.
A rear washer pipe leak can fill the motor or tailgate with fluid. Repair the pipe and connector contamination as well as the failed unit. Check that the washer jet or spindle passage is not blocked.
Safe removal sequence
- Record symptoms, codes, current and the physical park position.
- Obtain the correct battery-disconnection and trim-removal procedure.
- Mark blade positions on the glass with removable tape.
- Remove caps, nuts and arms using a suitable puller where seized.
- Take off scuttle or tailgate trim without damaging drains and clips.
- Ensure the circuit cannot operate unexpectedly before approaching the linkage.
- Disconnect the plug and support the motor/linkage assembly.
- Mark crank-to-linkage relationship before separating components.
- Inspect pivots, drains, seals and electrical terminals.
- Transfer only approved brackets or isolators to the exact replacement.
Setting the motor and linkage to park
Before connecting the crank, allow the motor to run and stop at its electrical park only when the service method permits safe bench or in-vehicle operation. Keep the loose crank isolated because it can move with high force.
Set the linkage at its mechanical datum, attach it without turning the motor and tighten the crank fastener to specification. On synchronised smart motors, use diagnostic alignment or learning procedures instead of manual assumptions.
Blade-arm installation
Clean corrosion from tapered splines without removing their form. Position arms at the stated screen marks after the mechanism has parked. Tighten nuts accurately, refit caps and wait any specified settling period.
Wet the screen thoroughly for the first full test. Confirm the blade never strikes the pillar, scuttle, trim or other blade and that the swept field covers the driver's view.
Faults after replacement
| Post-repair fault | Possible cause | Correction |
|---|---|---|
| Arms collide | Wrong linkage/crank timing or arm positions. | Stop immediately and reset to datum. |
| Park is too high | Arms fitted off-spline or incorrect motor. | Verify electrical park then reposition correctly. |
| Only one speed | Pinout, relay, brush circuit or coding issue. | Test commands and matched part number. |
| Motor overheats | Linkage drag or repeated end-stop stall. | Disconnect power and correct mechanical load. |
| Water enters cabin | Scuttle drains, grommet or membrane displaced. | Restore drainage and sealing. |
| Network fault remains | Wrong smart motor, wiring or missing setup. | Check communication and perform specified coding. |
Common mistakes
- Condemning the motor without checking seized pivots.
- Powering a loose crank while hands are within its travel.
- Moving blade arms to hide incorrect motor park.
- Testing repeatedly on a dry or iced windscreen.
- Replacing a fuse with a higher rating.
- Ignoring tailgate wiring and washer-fluid leaks.
- Fitting an RHD/LHD or network-incompatible motor.
- Failing to restore scuttle drains and water seals.
Visibility, urgency and UK MOT
Effective windscreen clearing is essential in rain and spray. If the driver's required swept area cannot be kept clear, do not continue in conditions that require the wipers. Stop safely and arrange repair. Never attempt to move arms by hand with the system live.
Wiper operation and the condition of the swept system are relevant to UK MOT inspection. Washers, blades, linkage and screen condition should be assessed together rather than treating the motor in isolation.
Wiper motor FAQs
Q: What does a wiper motor do?
A: It supplies geared torque to the linkage and controls the blades' park position.
Q: Does slow wiping prove the motor is worn?
A: No. Seized pivots, poor voltage supply and excessive blade drag can slow it.
Q: Why do the blades stop in the middle?
A: Park-switch, power, control, linkage or motor faults are possible.
Q: Are front and rear wiper motors interchangeable?
A: No. Their mounting, drive, control and park geometry differ.
Q: Does right-hand-drive specification matter?
A: Yes, because front linkage and sweep geometry can be different.
Q: Can a seized linkage damage a new motor?
A: Yes. Excessive current and heat can quickly overload it.
Q: Why should voltage be tested under load?
A: An unloaded meter reading can hide resistance that drops voltage only when current flows.
Q: Can the motor move unexpectedly during repair?
A: Yes. Park logic, rain sensing or a module command can energise it.
Q: Should wipers be tested on dry glass?
A: Avoid extended dry testing because friction overloads parts and can mark the screen.
Q: Does a smart wiper motor need coding?
A: Some require initialisation, synchronisation or coding according to the vehicle procedure.
Q: Why does a rear motor fill with water?
A: A failed spindle seal or leaking washer pipe can allow liquid inside.
Q: When should blade arms be refitted?
A: After the motor and linkage have reached and been verified at true park.
Q: Can a failed wiper motor affect the MOT?
A: Yes, ineffective clearing of the required windscreen area can affect inspection.