5441 Products
Your Current Vehicle
Or
Select Your Vehicle
Shop Brake Discs by Brand
Only manufacturers with matching products in the current catalogue are shown.
Brake Discs for Popular Car Makes
Choose a vehicle make with verified fitment for this part type.
Popular Vehicle Models for Brake Discs
Popular model families are ranked by the number of matching catalogue products.
Related Categories for Brake Discs
Explore related part types from the same catalogue group.
What brake discs are and why they matter
A brake disc, also called a brake rotor, is a precisely machined circular component attached to the wheel hub. Its two friction faces provide the surface against which the brake pads operate. The disc must absorb a large amount of energy, distribute heat, remain dimensionally stable and offer a consistent surface without becoming unnecessarily heavy. It is a wear component, even though it normally lasts longer than the pads.
Disc brakes are widely used on front axles and increasingly on all four wheels. The front system commonly handles a greater share of braking because vehicle weight transfers forwards during deceleration. Rear discs may be smaller, may incorporate a parking-brake mechanism, or may be combined with an electronic parking brake. Electric and hybrid vehicles still need friction brakes even where regenerative braking performs part of the slowing.
How a disc brake converts movement into heat
- Pedal force acts through the servo and master cylinder to create hydraulic pressure.
- Brake fluid transmits that pressure to the caliper at each commanded wheel.
- The caliper pistons move the pads against the rotating disc faces.
- Friction opposes rotation and converts kinetic energy into thermal energy.
- The disc stores and releases heat through its surfaces and, on a ventilated design, through internal air passages.
- When pedal pressure is released, hydraulic pressure falls and the pads move clear enough for the wheel to rotate freely.
Controlled friction is only part of the job. The disc must run true relative to the hub, maintain adequate thickness and dissipate heat without cracking or producing unstable friction. Tyres ultimately transmit braking force to the road, so even perfect discs cannot compensate for unsuitable or badly worn tyres.
What braking performance depends on
Stopping behaviour results from the whole braking and chassis system. Disc diameter affects leverage, while thickness and vane design influence heat capacity. Pad compound, caliper stiffness, hydraulic condition and brake-fluid temperature determine how the friction pair responds. Vehicle mass, speed, road gradient, tyre grip, load and driving style set the demand placed on those components.
Installation accuracy is equally important. Rust or debris trapped between the hub and disc can create lateral run-out. Uneven wheel-fastener torque can distort the assembly. A sticking caliper can overheat one area, while worn suspension or wheel bearings may be mistaken for disc judder. Diagnosis should consider the system rather than treating the disc as an isolated part.
Disc designs and typical applications
| Disc design | Construction and purpose | Typical considerations |
|---|---|---|
| Solid | A single friction section without internal vanes. | Compact and economical; often used where thermal demand is lower. |
| Ventilated | Two friction plates joined by internal vanes that move cooling air. | Greater heat capacity; common on front axles and heavier vehicles. |
| Grooved | Machined channels cross the friction face. | Can help clear surface material and provide a visual wear cue; may increase noise or pad wear. |
| Drilled | Holes pass through or partly into the friction section. | Can aid cooling and wet response when properly engineered; quality and crack resistance matter. |
| Two-piece | A separate friction ring is connected to a central bell. | Can reduce unsprung mass and manage expansion; requires application-specific hardware and procedures. |
| Integral hub or bearing | The disc is supplied with a hub, bearing or related encoder components. | Fitment, bearing torque and ABS compatibility must be checked carefully. |
Directional and handed discs
Some ventilated, drilled or grooved discs are directional. Curved cooling vanes may require a particular left- and right-hand orientation even where the surface pattern appears to suggest the opposite. Always follow the markings and fitting instructions supplied with the parts. Reversing a directional design can reduce its intended cooling performance.
Rear discs and parking brakes
A rear disc may have a drum-shaped inner section for separate parking-brake shoes, or the service caliper may also operate the parking brake. Electronic parking-brake systems can require diagnostic service mode before the piston is retracted. Forcing a mechanism back without the specified process can damage the caliper or actuator.
Development of brake-disc technology
Early automotive brakes commonly used drums. Disc systems became widespread because their open construction sheds heat and water effectively and makes pad inspection straightforward. As vehicles became faster and heavier, ventilated discs, larger calipers and electronically controlled brake-force distribution improved repeated-stop performance. Modern designs use computer-modelled vanes, carefully controlled cast-iron formulations, corrosion-resistant surface treatments and lighter multi-material constructions.
ABS, stability control, automatic emergency braking and brake-based traction systems can operate individual brakes independently of normal pedal input. This makes consistent mechanical condition increasingly important. Regenerative braking changes the duty cycle on hybrid and electric vehicles: reduced friction use may extend wear life, but it can also allow corrosion to develop if discs do not regularly clean their own surfaces.
Core components around the disc
Friction ring and cooling vanes
The friction ring is the working section contacted by the pads. Its mass absorbs heat and its exposed area releases that heat to the air. On ventilated discs, internal vanes connect the two faces and pump air through the rotor. Vane geometry, wall thickness and casting quality influence cooling and strength.
Disc bell, hub and fixings
The central bell locates the disc on the hub and transfers braking torque. Accurate centre-bore and mounting-face dimensions keep the disc concentric and square. Retaining screws usually locate the disc while the wheel is removed; wheel fasteners provide the main clamping load once assembled. They must not be used to pull a contaminated or poorly seated disc flat.
Pads, calipers and carriers
The pads and disc form a matched friction pair. The caliper applies force and the carrier allows correct positioning and movement. Seized sliders, corroded abutments or a restricted hose can keep a pad against the disc, creating rapid wear and local overheating. New discs cannot correct these underlying faults.
Shields, bearings and sensors
A backing shield helps protect nearby components and manage debris, but corrosion can bring it into contact with the disc. Wheel-bearing play can affect disc alignment. ABS wheel-speed information may come from a separate ring, the bearing seal or an integral encoder, so replacement arrangements must match the original system.
Materials, coatings and construction choices
| Material or treatment | Why it is used | Service implications |
|---|---|---|
| Grey cast iron | Good friction behaviour, heat capacity, damping and manufacturability. | Normal surface rust can appear quickly when wet; condition matters more than colour alone. |
| High-carbon cast iron | Formulation intended to improve thermal behaviour and refinement for a specific design. | Still requires the correct pad and application match. |
| Protective coating | Reduces corrosion on non-swept areas and may simplify preparation. | Follow instructions; do not remove a coating that is designed to remain in place. |
| Aluminium bell with iron ring | Reduces mass while retaining an iron friction surface. | Fasteners and floating hardware may have special replacement and torque requirements. |
| Carbon-ceramic composite | Very high temperature capability and low mass in specialist applications. | Expensive, application-specific and unsuitable for substitution without a complete engineered system. |
Wear, measurement and inspection
Disc thickness should be measured with a suitable micrometer at several positions around the friction ring, away from the outer lip. Compare the result with the minimum thickness marked on the disc or specified by the vehicle manufacturer. A visual check alone cannot establish remaining service life. Lateral run-out is checked with a dial indicator after confirming the hub and mounting faces are sound.
| Inspection point | What to look for | Why it matters |
|---|---|---|
| Thickness | Measurements at several points compared with the specified minimum. | Insufficient mass reduces strength and heat capacity. |
| Face condition | Heavy scoring, pitting, cracks, blue areas or uneven deposits. | Can affect friction, pad contact and structural confidence. |
| Run-out | Side-to-side movement measured at the specified radius. | Excess run-out can develop into thickness variation and judder. |
| Hub face | Rust scale, dirt, damage or raised areas. | Small mounting errors can become significant at the disc edge. |
| Caliper operation | Free sliders, sound boots and even pad wear. | Binding can overheat and rapidly damage the new friction pair. |
| Disc pair | Matching design and comparable condition across the axle. | Balanced braking depends on equivalent left and right components. |
Heat, fade and operating limits
Temperature rises rapidly with vehicle speed and mass. Repeated braking on a long descent can add heat faster than the disc can release it. The pad compound may fade, brake fluid may approach boiling point and seals or bearings may be stressed. A driver should use an appropriate gear on descents and avoid resting a foot on the brake pedal.
| Condition | Possible result | Appropriate response |
|---|---|---|
| Repeated heavy stops | Rising pedal effort, smell, fade or uneven deposits. | Reduce demand safely and allow controlled cooling; investigate persistent symptoms. |
| Dragging brake | One wheel becomes very hot and the vehicle may pull. | Stop safely and have the caliper, hose and hardware diagnosed. |
| Water applied to a hot disc | Rapid thermal shock and possible distortion or cracking. | Allow brakes to cool naturally. |
| Disc below service limit | Reduced thermal reserve and structural margin. | Replace the axle pair with the correct specification. |
| Track use on standard road parts | Components may exceed their intended temperature range. | Use a complete engineered setup suitable for the use and for any return to public roads. |
Fault symptoms and how urgently to respond
| Symptom | Possible causes | Urgency |
|---|---|---|
| Grinding or harsh scraping | Worn-out pads, severe disc damage, debris or loose hardware. | Stop using the vehicle until the braking system is inspected. |
| Judder under braking | Thickness variation, run-out, deposits, hub error, bearing or suspension wear. | Arrange diagnosis before further hard braking. |
| Crack or missing disc material | Thermal or mechanical failure. | Do not drive; recovery and immediate repair are appropriate. |
| Pulling to one side | Uneven friction, binding caliper, hydraulic fault, tyre or suspension issue. | Prompt professional assessment is required. |
| Soft or sinking pedal | Leak, air, boiling fluid or hydraulic component failure. | Treat as an immediate safety fault and do not continue driving. |
| Surface rust after standing | Moisture on the exposed iron face. | Light film often clears in normal use; persistent heavy corrosion needs inspection. |
Replacement and bedding guidance
Identify the exact brake option before ordering because one model can use several disc diameters and thicknesses. Replacement is normally carried out in axle pairs with new compatible pads. Support the vehicle on approved stands, follow the manufacturer's lifting procedure and never work beneath a vehicle supported only by a jack. Brake repairs require correct tools, measurements and torque data.
Clean the hub face without removing sound metal, check run-out where specified and keep oil or grease away from friction faces. Some discs require protective transport oil to be removed; coated discs may have different instructions. Check the caliper, carrier, sliders, hoses and shields before assembly. Tighten disc, carrier, caliper and wheel fasteners in the correct sequence and to the specified torque. Pump the pedal until normal contact is restored before the vehicle moves, then carry out the supplied bedding procedure in a safe setting.
Common mistakes to avoid
- Ordering from diameter alone and overlooking thickness, height, centre bore or brake option.
- Replacing a single disc instead of maintaining an equivalent axle pair.
- Reusing old pads on new discs and transferring an uneven wear pattern.
- Failing to clean and inspect the hub mounting face.
- Assuming all judder proves that a disc is warped.
- Ignoring a seized slider, damaged hose or uneven pad wear.
- Using impact tools without a final specified wheel-fastener torque procedure.
- Applying lubricant to the disc or pad friction surfaces.
- Moving the vehicle before restoring a firm pedal.
- Skipping bedding or performing repeated emergency-style stops on fresh components.
Upgrades, approvals and UK road use
Larger, grooved or two-piece discs should be considered as part of a complete brake system, not as styling changes. Disc, pad, caliper, wheel clearance, hydraulic balance and tyre capability must remain compatible. A poorly matched upgrade can reduce cold performance or introduce noise without improving real stopping distance. Material modifications may need to be declared to the vehicle insurer.
Replacement brake components may carry approval markings applicable to their design and market. Check the component documentation and vehicle requirements rather than relying on appearance. For the UK MOT, testers assess brake operation and visible defects including discs that are significantly and obviously worn, insecure, fractured, contaminated or likely to fail. The MOT standard is not the same as the manufacturer's service limit, and an MOT pass is not a forecast of future life. Cracks, severe wear, hydraulic faults or unpredictable braking require action regardless of test date.
Brake disc FAQs
Q: Should brake discs be replaced in pairs?
A: Yes. Replace left and right discs on the same axle together so their design, thickness and surface condition are equivalent.
Q: Do I need new pads with new discs?
A: New compatible pads are normally recommended. Used pads carry the wear pattern and deposits from the previous discs.
Q: How can I tell whether a disc is too thin?
A: Measure it with a suitable micrometer at several points and compare it with the specified minimum thickness. The outer lip is not an accurate gauge.
Q: Does brake judder always mean warped discs?
A: No. Thickness variation, uneven deposits, hub run-out, wheel-fastener torque, bearings and suspension faults can create similar symptoms.
Q: Is rust on a brake disc normal?
A: A light film after rain or standing is common on cast iron and often clears during normal braking. Heavy pitting or corrosion that does not clear should be inspected.
Q: Can I fit grooved discs with standard pads?
A: Only where the disc and pad manufacturers approve the combination for the vehicle. Compatibility is more important than the surface pattern.
Q: What causes blue marks on a disc?
A: They commonly indicate high temperature, sometimes from repeated braking or a dragging caliper. The cause and the condition of surrounding parts need checking.
Q: Why is one disc hotter than the other?
A: A sticking caliper, seized slider, restricted hose or uneven pad movement may be keeping that brake applied. Stop and investigate severe overheating.
Q: Are drilled discs better for road use?
A: Not automatically. A properly engineered drilled disc can have benefits, but strength, noise, pad choice and the actual vehicle duty all matter.
Q: Do electric vehicles wear out brake discs?
A: Yes. Regeneration may reduce friction wear, but discs can still corrode, bind or wear and remain essential for full braking performance.
Q: Can discs be skimmed instead of replaced?
A: Only if the manufacturer permits it and the finished disc will remain within all dimensional and run-out limits. Replacement is often the more appropriate route.
Q: Will worn brake discs fail an MOT?
A: Significantly and obviously worn, fractured, insecure or contaminated discs can result in failure. Service limits should still be followed even where the MOT threshold differs.
Q: When should I stop driving immediately?
A: Stop for a sinking pedal, major fluid leak, cracked disc, severe grinding, smoke, sudden pulling or a clear loss of braking performance.