1 Product
Your Current Vehicle
Or
Select Your Vehicle
Popular Part Types
Only part types stocked for this brand are shown.
Car Parts Categories
Browse the main catalogue areas in which this brand has matching products.
Other popular manufacturers of aftermarket automotive parts
Explore established alternatives with related products in the current catalogue.
Powermaster: understand the range before choosing
The Powermaster range here is one black rectangular bulkhead fitting, part S6354. The evidenced specification is 220–240 V mains, IP65, an ES/E27 lampholder for one GLS-form lamp up to 100 W, polycarbonate base/diffuser and no lamp included. The catalogue does not establish the fitting's electrical class, earthing arrangement, cable-entry method, ambient-temperature limit or compatibility with a particular LED lamp; the physical label and installation instructions must supply those details.
AutoMotoPart currently lists 1 Powermaster items. The largest Powermaster groups are 1 S6354 bulkhead-light entry. Powermaster totals can change, so a category count is orientation rather than proof that a particular reference suits a vehicle, workplace or job. The exact Powermaster listing, its current technical information and the item in front of you must agree.
What the Powermaster page actually covers
| Product group in this range | Current entries | Selection focus |
|---|---|---|
| S6354 rectangular bulkhead light | 1 | One S6354 black rectangular bulkhead: 220–240V, IP65, E27/ES GLS lamp holder, 100W maximum and lamp not included; verify class/earthing and installation details on the supplied fitting. |
There is no lamp, PIR, photocell, emergency module or low-voltage version in the live range. The fitting is a housing/lampholder, so actual illumination, colour rendering, colour temperature, efficiency and lifetime depend on the selected compatible lamp and operating environment.
Build a reliable shortlist
Confirm supply, circuit, location and required lighting performance. Read the S6354 label/instructions for electrical class, terminals, entries, mounting orientation, clearances and ambient limits. Select an E27 GLS lamp that remains within both fitting and lamp restrictions.
| Check | Why it matters | Useful evidence |
|---|---|---|
| Supply | S6354 is evidenced for 220–240V mains | Measured circuit and installation design |
| Lamp | One ES/E27 GLS-form lamp; lamp not supplied | Cap, envelope, enclosed rating and voltage |
| Power | 100W is a maximum, not required wattage | Lamp input watts and thermal suitability |
| Ingress | IP65 depends on complete seals and cable entry | Gland/grommet, gasket, orientation and substrate |
| Protection | Electrical class/earthing is not established here | Physical symbol, terminals and official instructions |
| Environment | Chemicals, heat, impact and UV can affect polycarbonate | Site assessment and material compatibility |
Do not install where hazardous-area, fire-rated, emergency, marine, food-safe or high-temperature certification is required unless the exact S6354 documentation explicitly provides it. IP65 alone does not establish those approvals.
Interpret 100W and E27 correctly
The E27 Edison-screw base defines the mechanical/electrical cap, while GLS describes a familiar general-lighting bulb envelope. Both must fit. The 100 W figure is the maximum for the fitting; a lamp's real heat distribution and electronics also matter. Never fit a larger envelope that touches the diffuser or blocks required air space.
LED retrofit lamps can use much less power for similar light output, but some are not rated for enclosed luminaires because driver temperature rises. Check the LED maker's enclosed-luminaire and ambient-temperature statements. Do not use a dimmable lamp unless the circuit and fitting arrangement are confirmed compatible, and do not add an oversize adaptor or multi-lamp splitter.
Electrical class and earthing must come from the label
A plastic housing does not prove double insulation. Inspect for the Class II double-square symbol, earth terminal, terminal block markings and conductor requirements. If Class I, continuity of the protective conductor is essential; if Class II, an unused circuit protective conductor still needs safe termination under the wiring rules. Never omit earth by assumption.
Isolate the correct circuit, lock off where required, prove the tester, prove dead and re-prove the tester. Route conductors without strand damage or trapped insulation, tighten terminals to instruction and maintain polarity. Complete protective-conductor, insulation, polarity and functional tests appropriate to the installation before energising.
Maintain IP65 through entries, seals and mounting
IP65 indicates dust-tight construction and protection against water jets under standard testing when assembled as designed. It does not mean submersible, pressure-washer proof at any distance, or suitable for every exposed location. Water can track down a cable or through a rear fixing if entries and substrate are poorly sealed.
Use only designated knockouts and the specified gland/grommet for cable diameter. Keep gasket faces clean, tighten diffuser screws evenly and do not overtighten polycarbonate. Seal wall penetrations using a compatible method that does not attack plastic. A drain/breather, if provided, must remain in the instructed orientation rather than being sealed casually.
Mount for heat, impact and service access
Verify that the wall or ceiling can support the fitting and that fixings suit the substrate and environment. Avoid hidden cables and pipes. Maintain clearance from combustible material and do not cover the fitting with insulation unless specifically permitted. ‘Vandal resistant’ is a catalogue description, not an IK impact rating or guarantee against deliberate attack.
Polycarbonate can be affected by solvents, oils, alkaline cleaners, heat and UV over time. Use only approved cleaners and a soft cloth. Plan safe access for lamp replacement without working from an unsuitable ladder or live circuit. In public/workshop areas, consider mechanical protection and exclusion during maintenance.
Commission and inspect the complete luminaire
Before energising, confirm all screws, seals and covers are present, the lamp does not exceed ratings, and no conductor is pinched. Test operation and observe for flicker, noise, odour or abnormal heat. Verify the selected lamp provides required illuminance without glare; lighting design cannot be inferred from wattage alone.
Periodically isolate and inspect for water marks, insects, cracked diffuser, brittle gasket, loose fixings, corrosion, discolouration or overheated lampholder contacts. Replace damaged components only with approved parts or replace the fitting. Do not drill extra holes, tape a cracked cover or increase lamp wattage to compensate for dirt or ageing.
From identification to a checked result
| Stage | Good practice for this range | Mistake to avoid |
|---|---|---|
| Design | Confirm 220–240V circuit, location, lighting and environmental needs | Choosing by 100W or IP65 alone |
| Verify | Read S6354 class, terminals, entries and lamp restrictions | Inferring earth/class from a plastic base |
| Install | Isolate/prove dead; mount, gland, wire and seal as instructed | Live work, extra holes or unsealed cable routes |
| Lamp/test | Fit compatible E27 GLS ≤100W and complete electrical tests | Assuming any E27 LED or bulb is suitable |
| Maintain | Isolate, cool and inspect seals, heat and water ingress | Pressure washing, taped cracks or higher wattage |
Record fitting model, circuit, protection, cable/gland, class/earthing evidence, lamp reference/wattage, test results and inspection interval. Future lamp changes must remain within the documented enclosure and thermal limits.
Reading real Powermaster references
The Powermaster names below are examples from the current range and show why the complete description matters. They are not universal Powermaster recommendations and should not be treated as a fitment list. Within Powermaster, a shared family word can conceal a different dimension, connector, material, pack format, operating condition or installation side.
| Example listing | What to verify beyond the name |
|---|---|
| Rectangular Bulkhead Light - Black - 100W | Powermaster S6354 black rectangular bulkhead: 220–240V, IP65, polycarbonate base/diffuser |
Some retailer pages contain conflicting later LED/60W fields for a similar code. This page follows the consistent live S6354 evidence and exact-reference electrical listings; the supplied label is final if revisions differ.
Common errors around Powermaster products
- Treating 100W as a lamp supplied or required output.
- Fitting an E27 lamp too large or not rated for an enclosure.
- Assuming plastic means double-insulated or no earth.
- Working without isolation, proving dead and electrical testing.
- Defeating IP65 with an unsealed entry or damaged gasket.
- Calling IP65 submersible or pressure-washer proof.
- Inventing PIR, emergency, dimming or hazardous-area functions.
- Taping cracks or increasing wattage to compensate for poor light.
Powermaster questions and answers
Q: What is the exact model?
A: Powermaster S6354 rectangular black bulkhead.
Q: What supply does it use?
A: The evidenced range is 220–240V mains.
Q: Which lamp cap fits?
A: One ES/E27 Edison-screw cap with GLS-form lamp.
Q: Is the lamp included?
A: No.
Q: What does 100W mean?
A: It is the maximum lamp input rating, not required wattage or light output.
Q: Can an LED lamp be used?
A: Only if E27/GLS dimensions, voltage, enclosed rating and thermal limits all suit.
Q: What is the ingress rating?
A: IP65 when correctly installed and assembled.
Q: Can it be submerged or pressure washed?
A: IP65 does not authorise submersion or unrestricted pressure washing.
Q: Does it need an earth?
A: Check the physical class symbol and terminals; do not infer from the plastic case.
Q: Can a DIY user wire it?
A: Mains work requires a competent person and compliance with current installation rules.
Q: Is it vandal proof?
A: It is described as vandal resistant, but no universal damage guarantee is made.
Q: What should inspections cover?
A: Diffuser, gasket, entries, fixings, water, heat marks, lampholder and electrical tests.
