1 Product
UNIBOND
Your Current Vehicle
Or
Select Your Vehicle
Popular Part Types
Only part types stocked for this brand are shown.
Car Parts Categories
Browse the main catalogue areas in which this brand has matching products.
Other popular manufacturers of aftermarket automotive parts
Explore established alternatives with related products in the current catalogue.
UniBond: understand the range before choosing
UniBond is Henkel's UK home-repair brand and is represented here by one broadly titled Power Tape listing. Current official information identifies Power Tape as a high-strength, fabric-reinforced, hand-tearable tape for fixing, binding and temporary repair on supported common materials indoors and outdoors. The collection evidence does not state the roll colour, width, length or product code, so those particulars must be confirmed on the item rather than imported from one current retail variant.
AutoMotoPart currently lists 1 UniBond items. The largest UniBond groups are 1 maintenance entry. UniBond totals can change, so a category count is orientation rather than proof that a particular reference suits a vehicle, workplace or job. The exact UniBond listing, its current technical information and the item in front of you must agree.
What the UniBond page actually covers
| Product group in this range | Current entries | Selection focus |
|---|---|---|
| Maintenance | 1 | Confirm exact Power Tape roll, colour, width, length and product code, supported substrate, clean-dry preparation, service temperature, temporary duty and safe removal plan. |
Only the family name Power Tape appears in the current collection record. UniBond's official UK page presently shows a black 50mm by 25m variant, while other colours or historic packs may exist. That current option does not prove the dimensions of every stock item. The long guide therefore controls selection by the delivered roll and its technical sheet rather than promising that a generic listing has a particular colour or quantity.
Build a reliable shortlist
Record the complete roll code, dimensions, colour, surface material, contamination, curvature, temperature, moisture, expected movement, duration and consequence of detachment. Decide whether the aim is identification, bundling, abrasion protection or a temporary repair. If a permanent engineered joint or safety function is needed, select the correct component or approved repair system instead.
| Check | Why it matters | Useful evidence |
|---|---|---|
| Exact roll | Power Tape variants can differ in size and colour | Wrapper code, width, length and current technical sheet |
| Substrate | Adhesion varies on metal, plastic, fabric, coatings and low-energy surfaces | Clean hidden-area trial on the actual material |
| Condition | Oil, dust, water and loose finish weaken the interface | Surface preparation and dry inspection |
| Service | Heat, cold, movement and pressure change demand | Measured temperature and failure consequence |
| Repair status | Tape can conceal damage that needs replacement | Temporary label, inspection interval and repair date |
| Removal | Strong adhesive or a blade can mark finishes | Accessible edge, safe cutter and substrate protection |
Do not interpret waterproof as universal underwater adhesion, indefinite immersion, certified pipe pressure or corrosion repair. Official technical information states resistance to air and water pressure up to 4 bar under its test context, but a site repair depends on pipe material, preparation, temperature, defect and wrapping geometry. A leaking pressurised service should be isolated and repaired by a competent method rather than used to recreate a headline laboratory figure.
Confirm the delivered Power Tape variant
Read the wrapper before use and keep its product code with any workplace record. Verify colour, roll width and length, storage condition and any use exclusions. Do not confuse Power Tape with UniBond Duct Tape, Electrical Tape or mounting tape; similar reinforced appearance does not transfer clean-removal, voltage, holding-load or application claims between families.
Inspect the roll edge for crushing, dirt or displaced adhesive. Tape stored in heat or direct sun may unwind or perform differently. Make a small trial on representative material and inspect both initial grab and removal effect. A trial on painted metal does not prove compatibility with a screen coating, headlining, vinyl graphic or aged plastic.
Prepare a sound clean and dry surface
The 2023 technical sheet specifies clean, dry surfaces and room-temperature application for optimum bonding. Remove loose contamination using a cleaner compatible with the substrate, then let volatile cleaner and water evaporate. Adhesive placed over rust scale, flaking paint or grease bonds to the contaminant rather than to a sound base.
Consumer material says the tape can stick to wet surfaces, but that feature should not displace the technical sheet's maximum-adhesion preparation. If an emergency damp-surface use is contemplated, isolate hazards, remove standing water where safe and regard the result as temporary and inspectable. Never dry a fuel or solvent-contaminated area with flame or uncontrolled heat.
Lay the tape without trapped folds or tension
Measure the required strip and tear by hand across the reinforced web where that gives a controlled edge. Use scissors or a guarded knife only when appropriate and cut away from the body and protected substrate. Avoid stretching the tape during placement because elastic recovery can lift corners or distort a flexible surface.
Place one end on sound material, smooth progressively and press firmly and evenly over the whole area. Remove air channels and wrinkles that can carry water. On a wrap, overlap consistently without hiding a sharp edge that can cut the tape. Apply multiple layers only after the first layer is well seated and the instructions support the intended task.
Keep temporary repairs visible and inspected
Mark a temporary repair with date, purpose and planned replacement where it might otherwise be forgotten. Inspect after the first temperature or moisture cycle and at an interval proportionate to failure risk. Look for edge lift, bubbles, stretching, adhesive creep, discolouration and movement of the underlying crack or joint.
Do not tape over warning labels, inspection points, drainage paths, vents, sensors or wiring faults. Tape does not restore lost metal section, cracked load-bearing plastic or degraded hose reinforcement. If damage grows, leakage returns or the substrate becomes hot, soft or chemically attacked, isolate the item and complete a proper repair.
Remove tape without creating new damage
Plan removal before wrapping inaccessible wiring or trim. Peel slowly at a low angle while supporting the substrate. Strong adhesive can lift weak coatings or leave residue. Use only a residue remover confirmed for both adhesive and surface, with ventilation and protective measures from its own safety information.
When a knife is necessary, use a guarded method and a barrier beneath the tape so the blade cannot cut a hose, cable, airbag fabric or painted panel. Collect strips immediately because adhesive tape can entangle tools and wildlife. Dispose of material contaminated with oil, chemicals or biological residue through the corresponding waste route rather than as clean general film.
From identification to a checked result
| Stage | Good practice for this range | Mistake to avoid |
|---|---|---|
| Define | Decide the task, duration and consequence of failure | Using tape as an automatic permanent repair |
| Verify | Read roll code, size, temperature and instructions | Borrowing claims from another UniBond tape |
| Prepare | Clean, dry and test a sound representative surface | Taping over oil, loose paint or active rust |
| Apply | Lay without stretch and press every edge evenly | Creating folds, water channels or hidden damage |
| Review | Label, inspect and replace the underlying fault | Leaving a temporary wrap unrecorded |
A useful record captures roll code, surface, cleaning method, trial result, layer count, date, temperature, temporary purpose and final repair deadline. For repeated workshop use, keep Power Tape separate from electrical and masking tapes so visual similarity cannot cause a wrong safety assumption.
Reading real UniBond references
The UniBond names below are examples from the current range and show why the complete description matters. They are not universal UniBond recommendations and should not be treated as a fitment list. Within UniBond, a shared family word can conceal a different dimension, connector, material, pack format, operating condition or installation side.
| Example listing | What to verify beyond the name |
|---|---|
| Unibond Power tape | UniBond Power Tape, exact wrapper code and roll dimensions, supported surface, clean-dry preparation, firm pressure, temperature range and temporary-use boundary |
The collection title alone does not establish colour or roll size. The verified current official variant is useful evidence for Power Tape characteristics, while the actual item must confirm its own code and dimensions. Waterproof, strong and long-lasting wording does not override substrate trials, repair inspection or the need to replace safety-critical damage.
Common errors around UniBond products
- Assuming the broadly titled listing is a specific 50mm by 25m roll.
- Transferring electrical-insulation or mounting-load claims from another tape.
- Applying over oil, dust, loose corrosion or weak paint.
- Stretching the tape so edges lift as it relaxes.
- Treating waterproof as approved permanent pressure-pipe repair.
- Covering structural, brake, fuel or electrical damage with tape.
- Forgetting to label and inspect a temporary repair.
- Cutting tape off without protecting the hose, cable or finish below.
UniBond questions and answers
Q: Which UniBond product is listed?
A: Power Tape, with the exact colour and roll dimensions requiring confirmation on the item.
Q: Can it be torn by hand?
A: Yes. Official technical information describes fabric-reinforced Power Tape as hand tearable.
Q: Is Power Tape waterproof?
A: UniBond describes it as waterproof, within the product's supported application and limitations.
Q: What temperature range is published?
A: Current official consumer information states -5°C to +70°C, subject to the exact delivered roll.
Q: Should the surface be wet or dry?
A: For maximum adhesion, the current technical sheet says clean and dry at room temperature.
Q: Can several layers be used?
A: Official guidance allows multiple layers for extra strength, but this does not create a certified structural repair.
Q: Can it permanently repair a leaking pipe?
A: Treat repair tape as temporary and isolate a pressurised leak for a competent permanent repair.
Q: Is it suitable for electrical insulation?
A: No electrical rating is established for Power Tape; use correctly rated electrical products and methods.
Q: Can it repair a fuel or brake line?
A: No. Do not use general tape as a safety-critical fluid-line repair.
Q: Will it damage paint?
A: Strong adhesive may mark or lift weak finishes, so test a hidden representative area first.
Q: How should it be pressed down?
A: Apply firm, even pressure over the full strip, paying particular attention to edges and overlaps.
Q: When should a taped repair be replaced?
A: At the planned earliest proper repair, or immediately if edges lift, damage moves or the hazard changes.
