61 Products
PORSCHE Car Parts
Porsche parts identification must start with the exact model type, chassis generation and factory equipment. A 911, Cayenne, Macan, Panamera or Taycan badge spans major changes in structure, engine position, propulsion, brakes and electronics. Record the VIN, model year, type/chassis code, engine or electric-drive code, gearbox, driven axles and option codes, then confirm markings, dimensions and connectors on the installed assembly.
Classic air-cooled 911 applications, later water-cooled flat engines and modern turbocharged units have unrelated lubrication, cooling, ignition and timing requirements. Front-engined Cayenne, Macan and Panamera variants add their own petrol, diesel or hybrid systems. Taycan uses high-voltage traction equipment and multi-circuit thermal management. A capacity, output figure or visual body style cannot establish a pump, sensor, gasket or service filter.
Manual, PDK dual-clutch and torque-converter transmissions need different clutches, controls and fluids. Transfer cases, electronically controlled differentials and final drives also have separate specifications. Use the exact Porsche-approved engine oil and documented level process; some models use electronic measurement with defined temperature and vehicle attitude. Do not infer lubricant from colour or add an unapproved friction modifier.
Brakes can differ by disc material, diameter, caliper, option code and axle. Iron and ceramic-composite systems require compatible friction and handling procedures. Suspension may be passive, electronically damped or air sprung, with active anti-roll or rear-steering equipment on some variants. Match wheels by diameter, width, offset, load, brake clearance and conventional or centre-lock fastening; use the stated tyre specification and closely matched circumference.
Diagnose oil pressure, coolant loss, PDK behaviour, air-suspension height, charging or chassis warnings with complete control-unit data and mechanical tests. One code can originate from wiring, supply voltage, a leak or a related actuator. Inspect underbody impact, heat shields, ducts, pipe routing and previous modifications before replacing expensive assemblies.
Use specified one-use hardware, tightening sequences and calibration. Centre-lock wheels, ceramic brakes, high-pressure fuel, air springs and high voltage require trained procedures and suitable tools. Restore brake cooling, undertrays and electrical grounds, then verify alignment and driver-assistance calibration. Do not drive with brake/steering defects, tyre damage, overheating, red warnings, fuel/oil leaks, unsafe ride height or battery impact; arrange recovery before UK road or MOT use.
Your Current Vehicle
Or
Select Your Vehicle
Shop Parts by Category
Choose a category to view parts for your selected vehicle.
Vehicle Models and Options for PORSCHE
PORSCHE Car Part Categories
Only categories with verified fitment products are shown.
PORSCHE Parts Catalogue Online
Browse catalogue-backed parts by vehicle system.
The type code is more useful than the silhouette
Porsche model names remain familiar while the engineering underneath changes. A 911 can be air cooled or water cooled, naturally aspirated or turbocharged and manual or dual clutch. Cayenne, Macan and Panamera cover their own generations, while Taycan starts from an electric architecture.
Identify model type, chassis, model year, engine or traction unit, gearbox and factory options. Production date matters because a technical change can occur within one registration year.
Build data and fitted evidence must converge
| Identity source | What it defines | Why to cross-check |
|---|---|---|
| VIN/model year | Type, market and original build range. | Later retrofit or assembly replacement. |
| Engine/e-drive code | Core propulsion and service family. | Ancillary and software revisions can differ. |
| Gearbox code | Manual, PDK or automatic unit and interfaces. | Final drive and calibration may still split. |
| Option code | Brake, suspension, wheel and equipment package. | Installed hardware may have been modified. |
| Control-unit identification | Software, active chassis and safety configuration. | Incorrect coding can present false equipment. |
| Part number/measurement | Physical revision, connector and geometry. | Internal material or calibration is not visible. |
Classic and modern 911 systems require separate thinking
Air-cooled flat engines regulate heat through oil and airflow, with model-specific oil tanks, lines, thermostats, fans and ignition. Later water-cooled engines add pumps, radiators, header tanks and complex coolant routing. The two groups do not share one warm-up, leakage or level-check method.
Engine generation also determines timing drive, valve control, turbo plumbing and electronic diagnostics. Preserve engine number and installed component references on older vehicles, where decades of repair may have changed the original specification.
Oil level is a procedure, not a quick assumption
Dry-sump, integrated-sump and electronically measured systems require different temperatures, idle conditions and vehicle attitude. Use the exact handbook or workshop process and named oil approval. Filling a cold or incorrectly positioned vehicle to an assumed mark can result in overfill.
Investigate pressure warnings, repeated consumption, fuel dilution, foaming or oil in coolant. A larger-capacity system can still be damaged quickly by loss of pressure. Never continue merely because the dashboard later clears.
Hot oil systems can retain pressure and temperature
Oil tanks, coolers and turbo lines may remain hot after shutdown. Allow controlled cooling, protect against burns and cap open lines. Prime opened lubrication circuits by the engine-specific method before load.
Thermal architecture follows propulsion and performance
| Application | Thermal systems to identify | Key service concern |
|---|---|---|
| Air-cooled 911 | Oil tank, external lines, thermostat and airflow. | Correct level state and unobstructed cooling. |
| Water-cooled flat engine | Radiators, pumps, header tank and bleed paths. | Air removal, cap pressure and leak tracing. |
| Turbocharged combustion | Charge cooling, turbo oil/coolant and exhaust shielding. | Heat soak, clean supply and hose integrity. |
| Hybrid model | Engine, battery, inverter and gearbox circuits. | Fluid separation and high-voltage isolation. |
| Taycan | Battery, motors, power electronics and cabin conditioning. | Multiple pumps/valves and trained HV work. |
| Performance brakes | Ducts, shields, disc and hub heat paths. | Correct airflow and material pairing. |
Cooling faults should be mapped by circuit
Cayenne, Macan and Panamera applications can have engine, charge-air, gearbox, hybrid and air-conditioning interactions. Taycan thermal management controls battery and power-electronics temperatures through several valves and pumps. Trace the circuit before ordering a component.
Use exact coolant chemistry and diagnostic bleed/activation routines. Pressure-test only when cold and within the stated limit. Overheating, steam, rapid loss or a traction-battery temperature warning requires shutdown and diagnosis.
PDK is not serviced as a conventional automatic
PDK uses two controlled clutches and preselected gear paths. Fluid sections, filters, fill temperature and adaptation differ by generation. A torque-converter automatic and a manual gearbox require their own unrelated service data.
Harsh take-up or a transmission warning can involve battery voltage, clutch wear, hydraulic pressure, temperature, selector data, engine torque control or mount movement. Preserve fault status and adaptation values before resets. Learning cannot repair worn friction material.
Transfer and differential systems are option dependent
All-wheel-drive and torque-vectoring systems vary across models and generations. Identify transfer unit, front/rear differential, electronic lock and ratio before selecting oil, pump or seal. A rear differential sharing a casing shape may contain different control hardware.
Tyre circumference and pressure influence coupling workload. Use approved size pairings and consider measured tread depth across axles. A warning after one tyre replacement should prompt tyre and wheel-speed comparison before a transfer unit is condemned.
Brake material changes service technique
Iron discs and ceramic-composite discs need compatible pads, sensors and handling. Ceramic surfaces must be protected from impact and inappropriate measuring or cleaning methods. Chip, crack and wear assessment follows the component procedure, not the limits for iron.
Caliper type, piston arrangement, disc direction, diameter, thickness and option code all matter. Retain brake-cooling ducts and shields. On vehicles with electronic parking brakes, use the specified service mode and post-repair calibration.
Centre-lock wheels require a controlled torque process
Where a central locking fastener is fitted, use the correct tool, vehicle restraint, thread/seat condition and model-specific torque method. The procedure may prescribe lubrication state, wheel loading and a verification sequence. Conventional five-bolt wheel torque is irrelevant.
Marking the nut without achieving the stated process is not proof of security. Inspect the wheel and lock components for damage and do not improvise extensions or impact tightening.
Air suspension stores energy after ignition-off
Cayenne, Panamera and other equipped variants can use air springs, a compressor, reservoir, valve block and level sensors. A low corner may result from a bag, line, valve, sensor, wiring or mechanical linkage. Record height data and leak-down before replacing parts.
Support the body independently and depressurise by the documented diagnostic method. Do not work under a vehicle held only by air pressure. After repair, calibrate level and check alignment and headlamp aim.
Active chassis components form a coordinated network
Electronic dampers, active anti-roll systems and rear-wheel steering, where fitted, depend on option-specific hardware and software. A passive-looking arm or actuator can have calibration or hydraulic connections not shared by the base suspension.
Test supply voltage, sensors, hydraulic pressure and mechanical free play. Coding a replacement to a generic vehicle order can disable the intended behaviour. Preserve original configuration and use supported programming power.
Hybrid and Taycan work crosses a high-voltage boundary
Traction batteries, inverters, chargers and motors can retain dangerous voltage after the display is off. Only trained personnel should isolate, secure, wait and prove dead using the precise model procedure. Remote keys and charging equipment must be controlled.
Battery impact, water ingress, heat, odour or smoke calls for an exclusion area and specialist recovery guidance. Do not lift beneath an unverified pack or open an enclosure. A weak 12-volt battery can cause no-ready symptoms without making high voltage safe.
Driver-assistance geometry is model specific
Forward radar, cameras and chassis sensors may need calibration after glass, bumper, alignment, spring or collision work. Verify correct brackets, ride height, wheel alignment and target setup. A communicating sensor can still be aimed outside tolerance.
Mechanical geometry comes before electronic calibration
If calibration will not complete, recheck thrust angle, sensor mount, glass and body structure. Repeated software attempts cannot straighten a bracket or compensate for an incorrect suspension height.
Use fault evidence to define safe limits
| Fault | Evidence to obtain | Immediate limit |
|---|---|---|
| Oil-pressure warning | Correct level state, mechanical pressure, leakage and pickup. | Stop the engine. |
| Coolant loss | Cold pressure, cap, pumps, radiators and bleed state. | Do not continue overheating. |
| PDK fault | Voltage, codes, clutch data, pressure and temperature. | Recover if engagement is unstable. |
| Low air-suspension corner | Leak-down, lines, valve, sensor and linkage. | Do not drive with tyre/body contact. |
| Brake vibration/pull | Material condition, run-out, calipers, tyres and hubs. | Severe imbalance is unsafe. |
| HV or battery-impact warning | Isolation state and trained structural/electrical assessment. | Do not charge or touch HV parts. |
A precise close-out protects high-value systems
- Capture VIN, type, model year, engine, gearbox and options.
- Compare installed labels, dimensions and software identity.
- Record fluid state, faults, pressure, height and wear.
- Choose components by material and calibration as well as fit.
- Control heat, fuel, spring, brake and voltage hazards.
- Use exact fluids, seals, one-use bolts and torque stages.
- Restore cooling ducts, heat shields, undertrays and grounds.
- Bleed and set levels under defined temperature conditions.
- Code, adapt, align and calibrate disturbed systems.
- Validate progressively and reinspect hot and cold.
Road legality is separate from performance intent
MOT condition covers tyres, brakes, steering, suspension, structure, lighting, visibility, restraints, emissions equipment and relevant warnings. Track-oriented pads, exhausts, wheels or ride heights must still be safe, road legal and declared to the insurer when used on public roads.
A test pass does not validate centre-lock procedure, oil level or high-voltage work. Fuel leaks, damaged ceramic brakes, unsafe ride height, steering defects and red warnings require repair or recovery before driving.
Practical Porsche parts FAQs
Q: Is the model badge enough to identify a Porsche part?
A: No. Confirm type, model year, codes and options.
Q: Are all 911 oil-level checks the same?
A: No. Follow the exact engine and system procedure.
Q: Can PDK fluid be replaced with generic ATF?
A: No. Use the precise unit specification and fill method.
Q: Does an adaptation repair worn PDK clutches?
A: No. Diagnose hydraulic and mechanical condition first.
Q: Can iron-disc wear limits be used on ceramic discs?
A: No. Material-specific inspection and limits apply.
Q: Is a paint mark enough for a centre-lock wheel?
A: No. Complete the specified torque and verification process.
Q: Does a low air-suspension corner prove bag failure?
A: No. Test lines, valves, sensors and linkage.
Q: Can one tyre affect an all-wheel-drive warning?
A: Yes. Compare circumference, pressure and wheel-speed data.
Q: Can a Taycan be safe because its display is off?
A: No. Formal isolation and proving dead are required.
Q: Does disconnecting 12 volts isolate the traction battery?
A: No. Follow the complete high-voltage procedure.
Q: Can a fault code identify the failed part?
A: It identifies a monitored condition requiring tests.
Q: Is ADAS calibration only needed after collision repair?
A: No. Glass, bumper and geometry work can require it.
Q: Does an MOT pass approve track modifications?
A: No. Road legality, insurance and safety remain separate.
Q: What confirms a Porsche repair?
A: Correct type data, secure assembly and verified fault-free operation.
