27 Products
WOLSELEY
This Wolseley parts collection brings together compatible listings for model families such as 1300, SIX, HORNET, 18/85 and 16/60. A model badge is only the first stage of identification: changes within a production run can alter the engine code, axle equipment, connector, belt layout, brake size or mounting arrangement. Use the vehicle selector, then confirm the product specification against the vehicle and removed part.
For cars, the most useful checks are engine size and code, fuel type, gearbox, body style, driven axle and build date. Optional sports, towing or heavy-duty packages can also change braking and suspension hardware. Never assume that a part fitted to one trim level automatically fits another with the same model name.
The current range is strongest in areas such as filters and routine service, braking, belts and timing, cooling and lighting and visibility. Diagnose the system before ordering: a warning light, leak, noise or uneven wear may be caused by wiring, mountings, contamination or another component rather than the obvious part. Check related seals, fixings, hoses and connectors, and follow the manufacturer’s repair sequence and tightening data.
Plan for the checks required after installation as well as the part itself. Some jobs need fresh fluid, a bleeding sequence, a diagnostic service mode, sensor calibration or a bedding procedure. Confirm these requirements in advance and arrange professional support where necessary. A replacement is only complete when the system has been commissioned, checked for leaks or warnings and shown to operate correctly.
Safety-critical work needs suitable tools and competence. Brakes, steering, wheels, fuel systems and high-voltage equipment should not be disturbed without the correct procedure. After fitting, complete any bleeding, priming, bedding, coding or calibration required, then carry out static and controlled functional checks before normal road use.
Use the model and product information below as a practical starting point, then verify every application-specific detail on the product page. Keep the vehicle details beside you while comparing alternatives, particularly where several dimensions or production notes are shown. Compatible Wolseley parts are listed in this collection.
Your Current Vehicle
Or
Select Your Vehicle
Choosing the right Wolseley components
The useful question is not merely “does this component mention Wolseley?” but “does it match this exact vehicle and assembly?” Production splits, regional specifications and optional equipment may all create differences within one model family. A dependable selection process combines vehicle data, diagnosis and a line-by-line comparison with the listing.
Applications represented in the selector include 1300, SIX, HORNET, 18/85 and 16/60. This is useful orientation, not a substitute for the final fitment checks. Where a model appears more than once, the body designation or code may identify a separate generation or derivative.
How to identify the exact application
- Record the registration, VIN, model series and build date.
- Confirm the engine or motor, fuel type, gearbox and driven axle.
- Note the body style, wheelbase, trim and any sports, towing or heavy-duty package.
- Diagnose the failed setup and record fault codes or measurements ahead of clearing them.
- Compare OE or cross-reference numbers, dimensions, connections, fitting position and included hardware.
- Read the installation notes for production splits, paired replacement, calibration and single-use fasteners.
For passenger vehicles, pay particular attention to engine code, body, brake package and transmission. If the removed component is available, compare it ahead of dismantling the vehicle further, while remembering that an approved supersession could have a revised appearance.
Wolseley model and body references
| Selector model | Application context | Details still specified |
|---|---|---|
| 1300 | passenger-vehicle model series | Verify generation, build date, powertrain and fitted equipment. |
| SIX | passenger-vehicle model series | Verify generation, build date, powertrain and fitted equipment. |
| HORNET | passenger-vehicle model series | Establish generation, build date, powertrain and fitted equipment. |
| 18/85 | passenger-vehicle model series | Confirm generation, build date, powertrain and fitted equipment. |
| 16/60 | passenger-vehicle model series | Confirm generation, build date, powertrain and fitted equipment. |
Model tables help organise a search, but they cannot show every engine, market or running change. A model sold over several years might use alternative filters, sensors, brakes or belts. Where the listing specifies a chassis range, engine code or “from/to” date, treat that note as part of the application requirement.
Model-specific service focus
1300
For this passenger-vehicle model series, identify the powertrain and compare filter dimensions, sealing faces and service specification. The 1300 name may span more than one derivative, so retain the selector's body or series code and reconcile it with the VIN, build date and removed part before ordering.
SIX
When working on a SIX, begin with braking: record the axle and braking assembly, then compare disc or drum size, friction shape and fitting hardware. Continue by reviewing the powertrain, production split and fitting position. If database and physical evidence disagree, investigate the vehicle history or superseded reference instead of choosing the closest-looking alternative.
HORNET
The practical focus for this passenger-vehicle model series is to use the engine code to verify belt profile, length or tooth count and the complete tensioning arrangement. Record the identification marks and measurements from the fitted component, then compare them with the HORNET listing. Include related seals, clips and single-use fasteners in the job plan where the service procedure calls for them.
18/85
The practical focus for this passenger-vehicle model series is to review connection layout, pressure rating, thermostat specification and any sensor or auxiliary-pump provision. Record the identification marks and measurements from the fitted component, then compare them with the 18/85 listing. Include related seals, clips and single-use fasteners in the job plan where the service procedure calls for them.
16/60
When working on a 16/60, begin with lighting and visibility: confirm the lamp function, cap, voltage, optical approval and exact front, rear, left or right position. Continue by reviewing the powertrain, production split and fitting position. If database and physical evidence disagree, investigate the vehicle history or superseded reference instead of choosing the closest-looking alternative.
Parts represented in this collection
Current product evidence for Wolseley is concentrated around filters and routine service, braking, belts and timing, cooling, lighting and visibility, ignition and starting and heating and air conditioning. Availability may change, and one category label may contain several designs. Use the table as an inspection guide, then rely on the individual product record for the final specification.
| Arrangement area | Important selection points | Related assessment |
|---|---|---|
| Filters and routine service | Match engine code, dimensions, sealing arrangement and specified interval. | Examine neighbouring parts before ordering. |
| Braking | Review axle, disc or drum dimensions, caliper assembly and any approval marking. | Inspect neighbouring components ahead of ordering. |
| Belts and timing | Confirm engine code, tooth or rib count, length and tensioning layout. | Assess neighbouring parts before ordering. |
| Cooling | Match hose connections, opening temperature, pressure rating and sensor provision. | Assess neighbouring parts before ordering. |
| Lighting and visibility | Review lamp function, voltage, cap, homologation and left/right position. | Examine neighbouring parts before ordering. |
| Ignition and starting | Confirm engine management setup, plug specification, connector and output rating. | Examine neighbouring parts before ordering. |
| Heating and air conditioning | Review refrigerant setup, connections, dimensions and production split. | Assess neighbouring parts before ordering. |
What reliable performance depends on
| Factor | Effect on the repair | Practical control |
|---|---|---|
| Exact application | A near match can bolt on yet have the wrong travel, output, pressure, friction area or calibration. | Check every listed dimension, code and fitting note. |
| Setup condition | Wear, blockage, poor alignment or electrical faults elsewhere may damage a replacement. | Inspect the complete assembly and specified the root cause. |
| Materials and fluids | Seals, friction materials and lubricants must tolerate the intended temperature and chemistry. | Use the specified grade, approval and cleaning method. |
| Installation | Contamination, incorrect torque or poor routing causes leaks, noise and early failure. | Follow model-specific service specification with suitable tools. |
| Commissioning | Some setups require bleeding, priming, bedding, coding or calibration. | Complete the prescribed procedure before road use. |
Diagnosis before replacement
Start diagnosis before dismantling. Record the complaint, warning messages and conditions in which the fault appears. Check fluid levels, fuses, wiring, visible leaks, looseness and signs of overheating. Scan data may support the investigation, but a fault code describes the condition detected by a control unit; it does not prove that the named part itself has failed.
Compare symptoms across operating states: cold and hot, stationary and moving, lightly and heavily loaded. For this car, relevant stresses may include journey length, load, road salt, towing, heat cycles and urban stop-start use. A fault that appears only under one condition often provides a better clue than the loudest symptom.
Construction, materials and specification
Automotive parts combine metals, elastomers, engineering plastics, friction compounds and electronic materials. Their grade and treatment matter. Heat-resistant rubber used in a coolant circuit is not automatically safe for fuel; a high-strength bolt is not interchangeable with one of the equivalent diameter but a varied pitch or tightening method; and a lamp with the equivalent cap might have a varied wattage or optical purpose.
| Specification | Typical variation | Why to verify it |
|---|---|---|
| Dimensions | Diameter, thickness, length, pitch, mounting centres and connector geometry. | Small differences may prevent fitment or change operating clearance. |
| Position | Front/rear, left/right, inner/outer, upper/lower or cylinder-specific. | Opposite-side parts can look alike but have mirrored fittings. |
| Rating | Load, pressure, voltage, current, temperature, speed or friction class. | A lower or unsuitable rating may create a safety or durability problem. |
| Material | Steel, alloy, rubber compound, polymer, ceramic or composite. | Material controls corrosion, flexibility, heat tolerance and chemical compatibility. |
| Approval | Vehicle-maker specification, E-marking or category-specific standard. | Road-use and setup requirements could depend on the specified approval. |
Technology and application changes
Older Wolseley applications might pre-date standardised diagnostics and can have undergone repairs or conversions during their working life. The fitted part, chassis specification and period parts data deserve more weight than a broad model-year assumption. Modern replacement materials might be beneficial, but dimensions, electrical polarity, hydraulic compatibility and originality requirements still need checking.
Networked control modules could require service mode, basic settings or calibration after mechanical work. Steering-angle, tyre-pressure, braking, lighting and emissions setups may all retain fault guidance. Use a diagnostic process suited to the vehicle; do not disconnect the battery as a universal reset, because doing so may lose learned values without curing the cause.
Wear, inspection and repair urgency
| Finding | Possible meaning | Recommended response |
|---|---|---|
| Fluid leak or fuel smell | Failed seal, hose, housing or joint. | Stop and investigate immediately if fuel or brake fluid is involved. |
| Grinding, knocking or increasing vibration | Excessive wear, looseness, contact or imbalance. | Avoid further use when steering, braking, wheels or drivetrain security might be affected. |
| Warning lamp or message | A monitored value or circuit is outside its expected range. | Read codes and test the setup; do not erase evidence first. |
| Uneven wear or pulling | Misalignment, restricted movement, pressure imbalance or tyre issue. | Examine both sides and measure the related geometry. |
| Overheating or burning odour | Drag, overload, poor cooling, short circuit or slipping drive. | Stop safely and allow diagnosis ahead of further damage occurs. |
| Intermittent operation | Loose connection, moisture, heat-sensitive electronics or internal wear. | Test under the conditions that reproduce the fault. |
Maintenance and installation guidance
Plan the job ahead of lifting or isolating the vehicle. Obtain the repair procedure, tightening values, fluid specification and any special tools. Support the vehicle on rated stands at approved points; a jack is a lifting device, not safe working support. Protect painted surfaces from aggressive fluids and use eye, hand and respiratory protection appropriate to the task.
Keep open hydraulic, fuel, intake and cooling assemblies clean. Start threads by hand, replace disturbed seals and single-use fixings where instructed, and route cables or hoses through their original clips. On paired safety components, follow the service guidance for axle or side-to-side replacement. Mixing incompatible friction materials, fluids or component ratings may create imbalance.
Once assembly, turn or move the mechanism by hand where appropriate, restore fluids, prime or bleed the circuit and reconnect arrangements in the specified sequence. Complete coding or calibration, then carry out a static check before a controlled low-speed test. Reinspect for leaks, heat, warning lamps, abnormal noise and loose fixings.
Common ordering and fitting mistakes
- Choosing by model name or image while ignoring build date and technical notes.
- Confusing a body designation with a alternative generation carrying the matching badge.
- Failing to check front/rear, left/right, axle or engine position.
- Assuming registration lookup removes the need to compare dimensions and references.
- Replacing a sensor without testing wiring, power, ground and the mechanical arrangement it monitors.
- Reusing locking hardware, seals or torque-to-yield bolts against the repair instruction.
- Applying general grease or sealant to a arrangement that requires a compatible specialist product.
- Skipping bleeding, bedding, priming, coding, service mode or calibration.
Upgrades, modifications and UK road use
An upgrade ought to answer a defined need such as heat capacity, load, corrosion resistance or repeated heavy use. A part described as performance-oriented is not automatically better for a road vehicle: cold response, noise, comfort, emissions compatibility and service life may be worse outside its intended operating window. Check how the change affects connected arrangements and declare relevant modifications to the insurer.
Brakes, tyres, steering, suspension, lamps, glazing, emissions equipment and warning arrangements may affect roadworthiness and the MOT result. An MOT is a minimum-condition check on the test date, not a maintenance schedule or proof that every part is appropriate. The vehicle must remain safe and roadworthy between tests, and lighting, emissions or safety parts ought to retain the approvals required for their application.
Wolseley parts FAQs
Q: How do I confirm a component fits my Wolseley?
A: Start with registration or VIN data, then match model series, build date, engine or motor, gearbox, position, dimensions, connector and reference numbers.
Q: Why does the equivalent model show more than one part?
A: Production changes, engine choices, body styles and optional equipment may create several valid specifications within one model name.
Q: Is a registration lookup conclusive?
A: It is a strong starting point, but imported vehicles, running changes and factory options mean the listing details and removed part ought to still be checked.
Q: May I order from the product photograph?
A: No. Images help recognition but can not show dimension, internal rating, pin function, side or production split.
Q: Needs to I use the VIN or engine code?
A: Use both when available. The VIN identifies the vehicle build, while the engine code may resolve powertrain-specific service components.
Q: Do related parts need replacement at the equivalent time?
A: Replace pairs, kits, seals and single-use hardware where the manufacturer instructs, and always inspect the complete surrounding assembly.
Q: What causes a new part to fail early?
A: Common causes include incorrect vehicle match, contamination, unresolved arrangement faults, wrong fluids, poor alignment and omitted commissioning steps.
Q: Does a fault code prove a sensor is faulty?
A: No. It records a detected condition. Wiring, supply, ground, leaks or mechanical faults might produce the equivalent code.
Q: May I fit Wolseley components myself?
A: Only where you have the correct specification, tools and competence. Safety-critical and high-voltage work needs to be handled by an appropriately trained person.
Q: What must be checked following fitting?
A: Recheck torque, routing, fluid level, leaks, warning lamps and normal operation, then complete any bedding, calibration or controlled road test required.
Q: Could the fault affect the MOT?
A: Yes, if it affects braking, steering, tyres, suspension, visibility, lighting, emissions, structure or a monitored safety assembly.
Q: When must the vehicle not be driven?
A: Stop when there is impaired braking or steering, an insecure wheel, fuel or brake-fluid leakage, severe overheating, restricted visibility or another immediate safety risk.