13 Products
FARECLA TRADE
Your Current Vehicle
Or
Select Your Vehicle
Popular Part Types
Only part types stocked for this brand are shown.
Car Parts Categories
Browse the main catalogue areas in which this brand has matching products.
Other popular manufacturers of aftermarket automotive parts
Explore established alternatives with related products in the current catalogue.
Farécla Trade: understand the range before choosing
Farécla is a surface-finishing specialist whose automotive range separates cutting compounds, finishing compounds and the applicators used to work them. The AutoMotoPart selection centres on established G3, G6 and G10 products, supported by 150 mm G Mop foam and threaded heads. The compound grade, paint system and defect determine the liquid or paste; the pad is a separate choice governed by task, backing system and machine.
AutoMotoPart currently lists 14 Farécla Trade items. The largest Farécla Trade groups are 10 maintenance entries, 3 valeting entries, 1 g mop 6in yellow compounding head 14mm entry. Farécla Trade totals can change, so a category count is orientation rather than proof that a particular reference suits a vehicle, workplace or job. The exact Farécla Trade listing, its current technical information and the item in front of you must agree.
What the Farécla Trade page actually covers
| Product group in this range | Current entries | Selection focus |
|---|---|---|
| Maintenance | 10 | Use G3 Advanced Liquid only where its stated paint-system and process guidance match the panel. |
| Valeting | 3 | Treat G6 Rapid Advanced Liquid and G6 Rapid Grade Paste as distinct formats, not the same product in different packaging. |
| G MOP 6IN YELLOW COMPOUNDING HEAD 14MM | 1 | Select G3 Regular Grade Paste by required quantity only after confirming its cut suits the paint and defect. |
The 14-item selection contains ten compound listings and four applicators. G3 accounts for liquid and paste cutting formats, G6 appears as dry-use liquid and rapid-grade paste, and G10 provides the finishing compound. Pack sizes range from 250 g to 3 kg for paste and from 500 ml to 1 litre for liquids. The applicators are all nominally six-inch or 150 mm products, but their attachment and intended stage differ.
Build a reliable shortlist
Begin by recording the paint type, whether it is original or refinished, how fully it has cured and the finest remaining defect. Read the exact compound data rather than selecting only by G-number. Then map the pad to the compound, backing arrangement and machine, keeping a clean finishing applicator away from cutting residue.
| Check | Why it matters | Useful evidence |
|---|---|---|
| Compound stage | Cutting and finishing products have different abrasive roles | Exact G3, G6 or G10 reference and Farécla process |
| Paint condition | Fresh, cured, aged and refinished coatings may require different products | Paint-system information and a controlled test area |
| Defect depth | A surface mark and a scratch through the coating cannot be treated alike | Clean inspection under suitable lighting and thickness awareness |
| Applicator type | Foam pads and threaded heads attach and behave differently | Product code, hook-and-loop face or 14 mm machine spindle |
| Machine setup | Diameter, backing plate, speed and orbit affect heat and cut | Polisher manual plus applicator and compound instructions |
| Finish control | Loaded pads or cutting residue can reintroduce marks | Separate clean pads, wipe-down method and inspection light |
A larger pack is economical only when the product is appropriate and can be stored as directed. For occasional work, a smaller closed container may reduce contamination and drying. Do not decant compound into an unlabelled bottle or combine grades to alter their cut.
G3 liquid and paste compounds
G3 Advanced Liquid Compound is listed in 500 ml and 1 litre sizes, while G3 Regular Grade Paste appears in 250 g, 400 g, 1 kg and 3 kg packs. Farécla describes the Advanced liquid as a fast-cutting, high-gloss one-step system and the Regular Grade Paste as a medium-to-high-cut rubbing compound for the paint systems and sanding level stated on its technical page. Those descriptions do not make the formats interchangeable on every coating.
Check the product instructions for hand or machine use, pad pairing, working quantity and any water requirement. Shake liquid only where directed and keep paste free from dried skin, grit and dirty tools. Work a measured test area and inspect after residue removal. If the scratch catches deeply, exposes primer or colour loss, polishing harder can thin surrounding sound paint without repairing the damage.
G6 rapid grades and dry-use process
The page includes G6 Rapid Advanced Dry Use Liquid Compound and G6 Rapid Grade Paste. Farécla identifies its dry-use liquid as a modern-paintwork product intended to be worked without adding water, while its comparison guidance places G6 paste with aged paint and particular cured refinishing systems. The shared G6 name therefore cannot replace the full product reference and technical sheet.
Dry use does not mean unlimited working time or a dust-free process. Use the recommended amount, keep the applicator controlled and stop when the compound has completed its stated cycle. Remove residue by the specified method and prevent dry debris collecting around trim or becoming embedded in the next pad. If a refinished panel's cure or coating type is unknown, obtain that information before using an aggressive compound.
G10 finishing and gloss refinement
G10 Finishing Compound occupies a different stage from the principal cutting products. Farécla describes it as a much finer abrasive for very light scratches, swirl marks and fading, particularly where a high-gloss final result is sought. It can refine appropriate paint after a cutting stage, but it will not rebuild missing coating or safely erase every visible scratch.
Use a clean finishing applicator and remove all earlier cutting residue from the panel, seams and surrounding equipment. Cross-contamination with a compounding pad can undo the refinement step. Inspect from several angles after wiping down because oils or residue can temporarily reduce the visibility of marks. Stop at an acceptable finish while preserving coating, rather than repeating passes solely to chase perfect reflections.
G Mop foams, heads and machine fit
The Advanced Compounding Foam and Advanced Polishing Foam listings are pad products, while GMH601 and the black finishing head specify 14 mm thread. Farécla's range information identifies the Advanced Polishing Foam as a multi-layer 150 mm applicator and links it with fine cutting and gloss enhancement. Its compounding foam has a different role. Colour is a useful cue within the range, but code, construction and intended product remain the reliable identifiers.
Before starting, verify machine spindle or backing-plate fit, pad diameter, maximum permitted speed and clearance around guards and handles. Centre hook-and-loop pads accurately and inspect thread and foam for damage. Prime only as instructed. Keep the face flat over broad areas, reduce risk at edges and body lines, and never allow a spinning pad to catch badges, apertures, loose masking or an adjacent panel.
Panel preparation, heat and pad care
Wash and decontaminate the surface using paint-safe methods before assessing defects. Embedded grit turns a controlled abrasive process into random scratching. Mask vulnerable textured plastics, sharp edges and openings where residue would be difficult to remove. Work away from hot panels, direct sun and airborne dust, and ensure the operator can see cable and pad position throughout the pass.
Clean pads often enough to prevent clogging and inspect for foam separation, hard residue or contaminated faces. A pad used for cutting should not become a finishing pad merely because it looks clean. Allow the panel and applicator to cool between sets, and measure temperature or coating thickness where the job requires it. Dispose of residue and damaged pads in accordance with the label and local arrangements.
From identification to a checked result
| Stage | Good practice for this range | Mistake to avoid |
|---|---|---|
| Assess | Identify coating, cure, defect depth and remaining paint condition | Choosing by colour or G-number alone |
| Pair | Match compound, pad or head, backing method and machine | Assuming every 150 mm applicator fits |
| Prepare | Clean, decontaminate, mask and arrange cool controlled lighting | Compounding grit into the paint |
| Test | Work a small area at the stated amount and speed, then inspect | Beginning with repeated aggressive full-panel passes |
| Refine | Use clean finishing equipment and stop at a safe acceptable result | Carrying cutting residue into the gloss stage |
Record the compound code, applicator, machine setting, number of passes and observed result for each paint system. That history is more useful than relying on memory or pad colour when returning to a multi-panel job.
Reading real Farécla Trade references
The Farécla Trade names below are examples from the current range and show why the complete description matters. They are not universal Farécla Trade recommendations and should not be treated as a fitment list. Within Farécla Trade, a shared family word can conceal a different dimension, connector, material, pack format, operating condition or installation side.
| Example listing | What to verify beyond the name |
|---|---|
| Farecla Trade GMH601 G MOP 6IN YELLOW COMPOUNDING HEAD 14MM | Full G3, G6 or G10 name, format, size and technical sheet |
| G6 Rapid Advanced Dry Use Liquid Compound - 1 litre | Paint system, cure state, defect depth and safe correction limit |
| G3 Advanced Liquid Compound - 1 litre | Pad code, 150 mm diameter, backing method, thread and machine speed |
| G3 Advanced Liquid Compound - 500ml | Cleanliness, panel temperature, inspection method and dedicated finishing tools |
| G Mop - 6in. Advanced Compounding Foam - Single | Full G3, G6 or G10 name, format, size and technical sheet |
| G Mop - 6in. Advanced Polishing Foam - Pack of 2 | Paint system, cure state, defect depth and safe correction limit |
| G10 Finishing Compound - 500ml | Pad code, 150 mm diameter, backing method, thread and machine speed |
| G3 Regular Grade Paste Compound - 250g | Cleanliness, panel temperature, inspection method and dedicated finishing tools |
Several pack sizes share the same compound name, while similarly sized G Mop products have different attachment and working roles. Use the complete code and description at both ordering and setup stages.
Common errors around Farécla Trade products
- Treating G3, G6 and G10 as simple coarse, medium and fine grades for every paint system.
- Using G10 to chase a scratch that has penetrated through the correctable coating.
- Assuming G6 liquid and G6 paste have identical application boundaries.
- Buying a 150 mm foam without checking hook-and-loop backing or a direct 14 mm thread.
- Working on a dirty or hot panel where contamination and heat alter the result.
- Running the pad on edges, body lines or trim with the same pressure as a broad panel.
- Using a compound-loaded pad for the final finishing stage.
- Repeating passes without checking temperature, coating condition and actual improvement.
Farécla Trade questions and answers
Q: What Farécla Trade products are available here?
A: The page contains G3, G6 and G10 compounds plus four 150 mm G Mop compounding, polishing and finishing applicators.
Q: Are G3, G6 and G10 interchangeable?
A: No. They differ by abrasive stage, format and stated paint application; use the exact product guidance.
Q: What is G10 intended to do?
A: It is a fine finishing compound for light scratches, swirls, fading and gloss refinement on suitable paint.
Q: Is G6 liquid the same as G6 paste?
A: No. The dry-use liquid and rapid-grade paste have different formats and application guidance.
Q: Can G3 remove every scratch?
A: No. Damage through the correctable paint layer requires repair rather than increasingly aggressive compounding.
Q: Does a 150 mm pad fit every polisher?
A: No. Check backing type, spindle thread, machine design, permitted diameter and speed.
Q: What does 14 mm thread mean?
A: It identifies a direct threaded fitting that must match the polisher spindle and the product instructions.
Q: Can a compounding foam be used for finishing?
A: Use the applicator pairing specified for the process and keep finishing pads free of cutting residue.
Q: Should water be added to a dry-use compound?
A: No, not unless the exact Farécla instructions state otherwise; dry-use identifies a specific process.
Q: Why test a small area first?
A: It shows whether the chosen combination corrects the defect without unnecessary heat or paint removal.
Q: When should a pad be cleaned or replaced?
A: Clean it when loading affects performance and replace it if foam, backing, thread or face is damaged.
Q: What should be checked after each pass?
A: Remove residue as directed and inspect defect reduction, gloss, temperature and coating condition under consistent light.
